ACKD 4890
Thread Starter
Senior Member
Joined: May 2001
Posts: 745
Likes: 0
From: springfield,IL
Car: T/A / Grand Am
Engine: 383 SBC
Transmission: glide
Axle/Gears: 9" ford 5.67
ACKD 4890
Can someone identify this memcal for me? Or tell me where I can find it. I have ordered Andrews cable and the pocket programer. Am going to try and start burning a chip this weekend. If this memcal won't work, can I use it untill I get the right combination? And then change the burned chip to a known 305 or 350 chip. Does the eprom have a calibration for the knock sensor, or are they located on the small chips on the memcal? Thanks.
------------------
87 GTA 355/700r4
ported&polished 083 heads
xe268h comp cam
1 5/8 blackjack alumicote
homebuilt y pipe,pasesetter 3in mandrel cat back.
ported/manifold,upper plentum, tpis maf.
airfoil, 24# svo injectors, hypertech stage 3 chip, underdrive pulleys, erson roller rockers, chromemolley pushrods,2100 stall, shiftkit, 373 10 bolt.
------------------
87 GTA 355/700r4
ported&polished 083 heads
xe268h comp cam
1 5/8 blackjack alumicote
homebuilt y pipe,pasesetter 3in mandrel cat back.
ported/manifold,upper plentum, tpis maf.
airfoil, 24# svo injectors, hypertech stage 3 chip, underdrive pulleys, erson roller rockers, chromemolley pushrods,2100 stall, shiftkit, 373 10 bolt.
Supreme Member
Joined: Jun 2000
Posts: 7,554
Likes: 1
From: In reality
Car: An Ol Buick
Engine: Vsick
Transmission: Janis Tranny Yank Converter
<font face="Verdana, Arial" size="2">Originally posted by cp87GTA:
Can someone identify this memcal for me? Or tell me where I can find it. I have ordered Andrews cable and the pocket programer. Am going to try and start burning a chip this weekend. If this memcal won't work, can I use it untill I get the right combination? And then change the burned chip to a known 305 or 350 chip. Does the eprom have a calibration for the knock sensor, or are they located on the small chips on the memcal? Thanks.
</font>
Can someone identify this memcal for me? Or tell me where I can find it. I have ordered Andrews cable and the pocket programer. Am going to try and start burning a chip this weekend. If this memcal won't work, can I use it untill I get the right combination? And then change the burned chip to a known 305 or 350 chip. Does the eprom have a calibration for the knock sensor, or are they located on the small chips on the memcal? Thanks.
</font>
Nope, not even close.
The electronic filtering for the K/S is on the memcal. What gets done with that info., is in the code.
Thread Starter
Senior Member
Joined: May 2001
Posts: 745
Likes: 0
From: springfield,IL
Car: T/A / Grand Am
Engine: 383 SBC
Transmission: glide
Axle/Gears: 9" ford 5.67
<font face="Verdana, Arial" size="2">Originally posted by Grumpy:
ACKD is for a 88 2.5 Manual
Nope, not even close.
The electronic filtering for the K/S is on the memcal. What gets done with that info., is in the code.
</font>
ACKD is for a 88 2.5 Manual
Nope, not even close.
The electronic filtering for the K/S is on the memcal. What gets done with that info., is in the code.
</font>
------------------
87 GTA 355/700r4
ported&polished 083 heads
xe268h comp cam
1 5/8 blackjack alumicote
homebuilt y pipe,pasesetter 3in mandrel cat back.
ported/manifold,upper plentum, tpis maf.
airfoil, 24# svo injectors, hypertech stage 3 chip, underdrive pulleys, erson roller rockers, chromemolley pushrods,2100 stall, shiftkit, 373 10 bolt.
Thread
Thread Starter
Forum
Replies
Last Post
