quick question about $6E
#1
Member
Thread Starter
Join Date: Feb 2005
Location: MD
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 firbird formula
Engine: 5.7l pony eater
Transmission: 700r4
Axle/Gears: 4.10
quick question about $6E
i noticed this is the mask for 90and up cars. mine being an 88 with MAF will i need a SD MAP sensor now, or just eliminate the cold start and remain using my MAF sensor?
#2
Supreme Member
iTrader: (1)
Join Date: May 2004
Location: houston
Posts: 2,262
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 POS monte carlo 2015 chevy P/U
Engine: 92 5.7 tpi 5.3
Transmission: 700r4 6L60E
Axle/Gears: 2.42 too high
Re: quick question about $6E
6E is for the 89 5.0 & 5.7 TPI.
8D is for 90 & up TPI.
with 6E, you need the MAF.
the cold start injector isn't used by 6E, most people cap off the fuel line for the cold start injector, for now you can just unplug the electrical connector on it.
8D is for 90 & up TPI.
with 6E, you need the MAF.
the cold start injector isn't used by 6E, most people cap off the fuel line for the cold start injector, for now you can just unplug the electrical connector on it.
#4
Senior Member
iTrader: (1)
Join Date: Apr 2004
Location: Prescott Valley AZ
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 Iroc Showcar - Saturday Nite Hun
Engine: 383 4-Bolt Truck Hyd Roller MiniRam
Transmission: B&M 700R4 - Edge 3200
Axle/Gears: BW 9 Bolt-TA Cover & Stud Kit - 3.2
Re: quick question about $6E
Hi,
So this would also be a good mask for a 87 350-A4 car
to start with.
Was going to start with 32B??
Whats the difference between 32B and $6E other than
the year from 87-89? Timing??
Didn't mean to hijack thread but was on the subject was going to post.
Just getting started with my APU1 and TP RT.
Been running a PCFormless starter chip that runs pretty
darn nice but needs a few changes.
Thanks
So this would also be a good mask for a 87 350-A4 car
to start with.
Was going to start with 32B??
Whats the difference between 32B and $6E other than
the year from 87-89? Timing??
Didn't mean to hijack thread but was on the subject was going to post.
Just getting started with my APU1 and TP RT.
Been running a PCFormless starter chip that runs pretty
darn nice but needs a few changes.
Thanks
Last edited by jaykar; 06-27-2007 at 05:31 PM.
#5
Supreme Member
iTrader: (1)
Join Date: May 2004
Location: houston
Posts: 2,262
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 POS monte carlo 2015 chevy P/U
Engine: 92 5.7 tpi 5.3
Transmission: 700r4 6L60E
Axle/Gears: 2.42 too high
Re: quick question about $6E
6E was the latest offering from GM, it does away with the cold start injector.
as far as i know, there is more info on 6E than 32 or 32B, i believe some of the tables are setup better also.
as far as i know, there is more info on 6E than 32 or 32B, i believe some of the tables are setup better also.
#6
Senior Member
iTrader: (1)
Join Date: Apr 2004
Location: Prescott Valley AZ
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 Iroc Showcar - Saturday Nite Hun
Engine: 383 4-Bolt Truck Hyd Roller MiniRam
Transmission: B&M 700R4 - Edge 3200
Axle/Gears: BW 9 Bolt-TA Cover & Stud Kit - 3.2
Re: quick question about $6E
Thanks,
Thru the years got pretty proficient with the Carters
Rochesters,Holleys and distributor setups for different
setups.
Now going to have to use the keyboard to set it up to
run FI
Been doing alot of reading but Lite Bulb hasn't come
on yet. Think I have the basics
Later
Thru the years got pretty proficient with the Carters
Rochesters,Holleys and distributor setups for different
setups.
Now going to have to use the keyboard to set it up to
run FI
Been doing alot of reading but Lite Bulb hasn't come
on yet. Think I have the basics
Later
Thread
Thread Starter
Forum
Replies
Last Post