Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
Thread Starter
Member
Joined: Jun 2006
Posts: 463
Likes: 9
From: Milford, OH
Car: 91 Z28 - using 87 electricals
Engine: 383 HSR EBL
Transmission: 700R4 - Stage 3 Fixed Pressure
Axle/Gears: GM 3.08 POSI
Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
Hey All,
I am looking for a wiring or pinning diagram for the bulkhead connector on the drivers side firewall underneath and behind the mounted relays for a 91 Z28 and an 87 Irocz both with VIN F.
I bought a new body, a 91 Z28 and I need to see how much and what differences there are in the pinning of that connector so I can get my engine wired in.
This bulkhead connector should connect the fuse box to the headlights and the engine harness.
I will be using a painless engine harness and that will handle most of the heavy lifting, but I would like to do this job right.
Thanks,
I am looking for a wiring or pinning diagram for the bulkhead connector on the drivers side firewall underneath and behind the mounted relays for a 91 Z28 and an 87 Irocz both with VIN F.
I bought a new body, a 91 Z28 and I need to see how much and what differences there are in the pinning of that connector so I can get my engine wired in.
This bulkhead connector should connect the fuse box to the headlights and the engine harness.
I will be using a painless engine harness and that will handle most of the heavy lifting, but I would like to do this job right.
Thanks,
Joined: Dec 2004
Posts: 16,737
Likes: 994
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
C100 diagrams can be found at the bottom of this link.
http://www.austinthirdgen.org/?pid=19
http://www.austinthirdgen.org/?pid=19
Joined: Aug 1999
Posts: 5,259
Likes: 459
From: RI
Car: 1984 Camaro Berlinetta
Engine: LT1
Transmission: T56 6-speed
Axle/Gears: 4.11 LS1 Rear End
Re: Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
Re: Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
Thread Starter
Member
Joined: Jun 2006
Posts: 463
Likes: 9
From: Milford, OH
Car: 91 Z28 - using 87 electricals
Engine: 383 HSR EBL
Transmission: 700R4 - Stage 3 Fixed Pressure
Axle/Gears: GM 3.08 POSI
Thread Starter
Member
Joined: Jun 2006
Posts: 463
Likes: 9
From: Milford, OH
Car: 91 Z28 - using 87 electricals
Engine: 383 HSR EBL
Transmission: 700R4 - Stage 3 Fixed Pressure
Axle/Gears: GM 3.08 POSI
Re: Wiring/Pinning Diagram needed for Firewall Bulkhead Connector
C100 diagrams can be found at the bottom of this link.
http://www.austinthirdgen.org/?pid=19
http://www.austinthirdgen.org/?pid=19
Thread
Thread Starter
Forum
Replies
Last Post
mitchberry
Engine Swap
1
Sep 29, 2012 01:29 PM
cmexlr8
Engine Swap
6
Sep 11, 2009 06:35 PM