Jeep Steering Shafts
Thread Starter
Junior Member
iTrader: (2)
Joined: Apr 2003
Posts: 28
Likes: 0
From: usa
Car: 85 Trans Am
Engine: 305 LG4
Transmission: 700-R4
Axle/Gears: 3.08
Re: Jeep Steering Shafts
TTT
Happy New Year
Happy New Year
Last edited by T-Top T/A; Jan 1, 2013 at 10:17 AM. Reason: added picture
Junior Member
iTrader: (1)
Joined: Mar 2002
Posts: 4
Likes: 0
From: Saratoga Springs NY
Car: 2000 SS 1991 Z28 VERTS
Engine: LS1 TPI
Transmission: T56 TKO500
Axle/Gears: 4.10 3.73
Re: Jeep Steering Shafts
I'll take one. PM me your info. Do you have any of the Astro bearings by any chance?
Thread Starter
Junior Member
iTrader: (2)
Joined: Apr 2003
Posts: 28
Likes: 0
From: usa
Car: 85 Trans Am
Engine: 305 LG4
Transmission: 700-R4
Axle/Gears: 3.08
Re: Jeep Steering Shafts
I have 2 Astro Van shafts. These have been re-clock, but have NOT been welded.
$40 total shipped each in lower 48.....
$40 total shipped each in lower 48.....
Thread Starter
Junior Member
iTrader: (2)
Joined: Apr 2003
Posts: 28
Likes: 0
From: usa
Car: 85 Trans Am
Engine: 305 LG4
Transmission: 700-R4
Axle/Gears: 3.08
Member
iTrader: (5)
Joined: Jun 2006
Posts: 276
Likes: 0
From: Montreal, Canada
Car: '83 Berlinetta
Engine: 383 CI
Transmission: T56
Axle/Gears: 3.73, Eibachs, Tokiko Illuminas,
Re: Jeep Steering Shafts
I finally got around to putting the Jeep shaft into my '83 Camaro.
What a difference!
Bump for a worthwhile upgrade.
Jon.
What a difference!
Bump for a worthwhile upgrade.
Jon.
Joined: Jul 1999
Posts: 12,096
Likes: 126
From: SALEM, NH
Car: '88 Formula
Engine: LC9
Transmission: 4L60E
Axle/Gears: 3.89 9"
Re: Jeep Steering Shafts
I don't feel like searching through 300 posts on the thread linked earlier.
Just plain and simple, is this direct bolt in? My shaft is seized so I'll buy one if I don't have to spend 3 hours modifying things, or I'll just get a stock one from Don.
Let me know.
-- Joe
Just plain and simple, is this direct bolt in? My shaft is seized so I'll buy one if I don't have to spend 3 hours modifying things, or I'll just get a stock one from Don.
Let me know.
-- Joe
Thread Starter
Junior Member
iTrader: (2)
Joined: Apr 2003
Posts: 28
Likes: 0
From: usa
Car: 85 Trans Am
Engine: 305 LG4
Transmission: 700-R4
Axle/Gears: 3.08
Re: Jeep Steering Shafts
Yes, Its a direct bolt in, Just ned to put a small notch in the end of the steering column. You have a PM
Joined: Jul 1999
Posts: 12,096
Likes: 126
From: SALEM, NH
Car: '88 Formula
Engine: LC9
Transmission: 4L60E
Axle/Gears: 3.89 9"
Re: Jeep Steering Shafts
You are right. Snaking the old one out past the brake lines kind of sucked.
The new one went right in. Used a round file on the column. Measured, marked, filed, and done.
Glad it showed up today as tomorrow the car is off to media blast. Needed to steer it!
-- Joe
The new one went right in. Used a round file on the column. Measured, marked, filed, and done.
Glad it showed up today as tomorrow the car is off to media blast. Needed to steer it!
-- Joe
