[CA] Looking for a strut brace!!!
Thread Starter
Supreme Member
Joined: Apr 2009
Posts: 2,852
Likes: 2
From: Scottsdale, AZ
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Looking for a strut brace!!!
im lookin to buy a strut tower brace for my 89 GTA...like this one
http://www.summitracing.com/parts/EDL-5226/
Mikey
http://www.summitracing.com/parts/EDL-5226/
Mikey
Supreme Member
iTrader: (1)
Joined: Dec 2006
Posts: 2,403
Likes: 4
From: ms. gulf coast
Car: 91 R/S , 89 dodge p/u
Engine: L31 GM crate re-cammed , 318
Transmission: T-5 , 4 speed auto
Axle/Gears: 3.42 , ?
Re: Looking for a strut brace!!!
do you have a question ? i have that one as many others here do . it's pretty good quality , does the job . i also have a TDS wonderbar . the combination keeps the front end pretty tight . question ????
Thread Starter
Supreme Member
Joined: Apr 2009
Posts: 2,852
Likes: 2
From: Scottsdale, AZ
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: Looking for a strut brace!!!
umm...no..i was seeing if anyone had one they were trying to sell b/c i dont really wanna pay that much for it unless i have too.
Supreme Member
iTrader: (1)
Joined: Dec 2006
Posts: 2,403
Likes: 4
From: ms. gulf coast
Car: 91 R/S , 89 dodge p/u
Engine: L31 GM crate re-cammed , 318
Transmission: T-5 , 4 speed auto
Axle/Gears: 3.42 , ?
Re: Looking for a strut brace!!!
you should have posted under parts wanted . not trying to give you a hard time . good luck .
Banned
iTrader: (12)
Joined: Jul 1999
Posts: 12,212
Likes: 13
From: Bertram (outside Austin), TX
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: Looking for a strut brace!!!
I had one of those Edelbrock 3-pts. Replaced it with a UMI 2-pt. The Edelbrock seemed a little too thin, especially the 2 strut tower mounts for it.
The UMI one was easier to install, and required no drilling of holes to mount, unlike the Edelbrock one. Now I have empty holes, that I'll weld shut & make disappear someday.
The UMI one was easier to install, and required no drilling of holes to mount, unlike the Edelbrock one. Now I have empty holes, that I'll weld shut & make disappear someday.
Trending Topics
Banned
iTrader: (12)
Joined: Jul 1999
Posts: 12,212
Likes: 13
From: Bertram (outside Austin), TX
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: Looking for a strut brace!!!
BTW....Either way you go, the GTA hood is going to be a interference problem for the STB. The UMI one fit better & required less underhood brace trimming.
If your not comfortable with cutting/hammering on your car.....A commercially made STB is not for you.
If your not comfortable with cutting/hammering on your car.....A commercially made STB is not for you.
Last edited by Stephen; Feb 4, 2010 at 04:48 PM.
Thread
Thread Starter
Forum
Replies
Last Post
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
7
Oct 8, 2015 08:34 PM
tcflint
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 27, 2015 05:58 PM
