Flowtech Terminator mufflers
#1
Member
Thread Starter
Join Date: Mar 2001
Location: Turnersville, NJ
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
Flowtech Terminator mufflers
Since the "Search Option" is down, I was hoping to get some opinions from anybody that has used these mufflers. This is the black muffler that says "Bite Me" on the casing. I was j/w how the sound was........deepness, volume, etc. Thanks!
#2
Supreme Member
Join Date: Apr 2001
Location: USA
Posts: 4,969
Likes: 0
Received 0 Likes
on
0 Posts
Car: yy wife, crazy.
Engine: 350, Vortecs, 650DP
Transmission: TH-350
Axle/Gears: 8.5", 3.42
I don't have those, but I do have the cheap Flowtech "Raptors" on my '83 1/2 ton. They cost about $15/ea and sound pretty darn good IMO. They've got a nice deep sound without sounding raspy.
I know they're not the same muffler, but they're the same company. And if the cheap ones sound good, then the 'slightly more' expensive ones should sound better, right?
I know they're not the same muffler, but they're the same company. And if the cheap ones sound good, then the 'slightly more' expensive ones should sound better, right?
#3
I had a afterburner on my 97 nissan truck (with a header) mean as hell sounding...till it blew the back half of the muffler off =/. Other then that..good mufflers don't know about the black one though =/
#4
Supreme Member
Join Date: Jan 2003
Location: ny-lindy
Posts: 1,053
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Iroc z hardtop
Engine: peanut LB9
Transmission: slopomatic TH700R4
i've been looking at that muffler to. i might just buy it, i've seen charts on it and i must saythat they look good. 2 .5" crossflow flows better than a flowmaster. i also like the price.
#5
Member
Thread Starter
Join Date: Mar 2001
Location: Turnersville, NJ
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
Well, I was set on getting the Flowtech Terminator muffler after reading revies, charts, and prices. But, now I am also considering their AfterBurner muffler. The Terminator is $68 and the AfterBurner is $50, from SummitRacing. I really want an aggressive sound. Any opinions?
#7
Member
Thread Starter
Join Date: Mar 2001
Location: Turnersville, NJ
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
I am looking for a crossflow with 2.5" inlet/outlets? I could get a 3" and use an adaptor but, I would like to avoid that? I have also considered.....hooker aerochamber, flowmaster 80 series, and the edelbrock rpm. Right now I have a headers, gutted cat, and a Dynomax Super Turbo cat-back on the LO3. Still too quiet though. Thanks for the replies!
Trending Topics
#8
Supreme Member
Join Date: Jan 2003
Location: ny-lindy
Posts: 1,053
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Iroc z hardtop
Engine: peanut LB9
Transmission: slopomatic TH700R4
i have stock manifolds, 3" random tech cat and a 3" intermidate ipe with muffler from a napa. if urs is quiet then what is mine lol
headers,ram jet cam and reworkin the heads are in plan for late spring
headers,ram jet cam and reworkin the heads are in plan for late spring
#9
Junior Member
Join Date: May 2002
Location: east coast, usa
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Summit Fully welded is a great muffler for 39 bucks!
it took second a few years ago in one of the shootout's.
(mufflers under 40 bucks, think it was Car Craft.)
Borla took first, however the Borla was supposedly louder.
It's quiet inside the vehicle, but has a quiet rumble at idle, and is throaty, but not ignorant at 3000 rpm's
I've had it on two trucks now..... and am ready to use two on the 327 pickup......
they don't offer a crossflow design though.
Truck muffler.
my .02
Chris400
(I hate flowmaster's drone in the car at 50 mph.......)
:lala:
it took second a few years ago in one of the shootout's.
(mufflers under 40 bucks, think it was Car Craft.)
Borla took first, however the Borla was supposedly louder.
It's quiet inside the vehicle, but has a quiet rumble at idle, and is throaty, but not ignorant at 3000 rpm's
I've had it on two trucks now..... and am ready to use two on the 327 pickup......
they don't offer a crossflow design though.
Truck muffler.
my .02
Chris400
(I hate flowmaster's drone in the car at 50 mph.......)
:lala:
#11
Junior Member
Join Date: May 2002
Location: east coast, usa
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Summit is like Radio Shack.....
they have everybody else's stuff rebadged as their own....
It probably is a Flow.
The Fully Welded Muffler sounds alot like a flow, just without the drone.
and hey, for 40 bucks!
Chris400
they have everybody else's stuff rebadged as their own....
It probably is a Flow.
The Fully Welded Muffler sounds alot like a flow, just without the drone.
and hey, for 40 bucks!
Chris400
#12
Member
Join Date: Sep 2002
Location: montreal, QC Canada
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
Car: Malibu 80, T/A 87, S-15 87
Engine: 267 Bu, 305 T/A, 350 S-15
Transmission: Auto Bu, 5spd T/A, Auto S-15
I have heard that the Terminator muffler sound will change with time... too bad the search is still down, i'm sure someone asked about that muffler before.
#13
Supreme Member
Originally posted by chris400
Summit is like Radio Shack.....
they have everybody else's stuff rebadged as their own....
It probably is a Flow.
The Fully Welded Muffler sounds alot like a flow, just without the drone.
and hey, for 40 bucks!
Chris400
Summit is like Radio Shack.....
they have everybody else's stuff rebadged as their own....
It probably is a Flow.
The Fully Welded Muffler sounds alot like a flow, just without the drone.
and hey, for 40 bucks!
Chris400
Originally posted by yanfoo
I have heard that the Terminator muffler sound will change with time... too bad the search is still down, i'm sure someone asked about that muffler before.
I have heard that the Terminator muffler sound will change with time... too bad the search is still down, i'm sure someone asked about that muffler before.
#14
Senior Member
iTrader: (2)
Join Date: Sep 2002
Location: Central Va.
Posts: 766
Likes: 0
Received 0 Likes
on
0 Posts
Car: 82' Z28 IROC Clone (SOLD)
Engine: 355
Transmission: Built TH-350
Axle/Gears: 3.73 Moser 12 bolt
My friend had Terminators on his truck and they sounded awful...VERY VERY quiet mufflers..He had them for 2 months before he couldn't take it anymore and put differnt mufflers...He's selling his if you want them 2 1/2 in and out 2 of them!
Thread
Thread Starter
Forum
Replies
Last Post
[GA] Shorty headers
Night rider327
Engine/Drivetrain/Suspension Parts for Sale
0
09-16-2015 02:20 AM