You know what it says i just wanna see what is out there and how it looks. lets also post make and model of them. price and ride quality if you can. maybe even installation notes?

 

https://www.thirdgen.org/forums/atta...-new-seats.jpg

Here are mine

 

what kind are they?

 

 

this is my best picture.. jaz race seats. that is all i know. bought them second hand from a friend for 50 bucks. install was difficult and not complete. home made brackets

 

Corbeau Forza's on modified factory seat rails. Driver side power, passenger side manual.
About 500 bucks for the pair racingseatsusa.com



another shot of them before the interior was done

 

those are killer!! you can see the make but what is the model? price? install notes? ride?

 

They look like recaro sportster cs? I would love to eventually get a pair of those for my car!

 

Recaro CS Sportster, about 1600 a pop, 1900 for all leather

 

I love my seats. They hug so well and fit perfect. Price wasn't bad either. Corbeau A4

https://www.thirdgen.org/forums/inte...ing-seats.html

 

Twin Turbo those are some real nice seats. The best I've seen to date.

 

Here are the pictures of my corbeau A4 seats. I got a great deal on them at www.apexperformance.net







They are great!

https://www.thirdgen.org/forums/inte...ing-seats.html

 

That's a nice looking Nova in the background. What year?

 

Hmmm I have Cobreau A4s in my vette. Glad they work in all 80s cars lol

 

the recaro seats are really nice to have, i have the sports in my car and i can pretty much drive anywhere without losing comfort. I got really lucky with mine buying them straight from the factory for two seats it was 700 but they discounted them because they where on back order for almost a year. mine are black suede with titanium black inserts.

 

They are Procar by Scat. Got them from Summit. It's $452 for both seats and brackets.

 

Did you happen to weigh them?

 

It's a '72 Nova. Stole from a little old lady for three hundred bucks. Runs great.

 

No I didn't weigh them. They are lighter than the stock seats, I can tell that just from lifting them up. Don't know the weight though.

 

RAPID RIDES 09 051

 

????????????

 

https://www.thirdgen.org/forums/pict...pictureid=9781 Sorry !! 96 Trans Am !!

 

those are factory seats, not aftermarket.

 

Yeah i want this to eventually turn into a long thread of the aftermarket. We have all seen the 4th gen. I wanna see aftermarket

 

Corbeau GTS II.
They are very comfortable but they sit about an inch or two taller than stock seats.
I think they were around $1000 for the pair with brackets 10 years ago. My friend bought them for his 82 Trans Am then sold them to my brother and then sold to me.




this is when they were just installed in 2000 in the 82,




They faded quite a bit over the years and my friend complained about the fading to Corbeau so they sent him a brand new set of seat covers, which I have and will put on when the current covers get really bad.

 

I love some of these seats, especially Orr89's

 

Do the a4 s ride higher? My seats were a little high and my helmet hit my t top. I dont want that in my new car

 

My A4s with cobreau bracket were lower than my seats. Then again my vette seats were very cushioned in the *** area.

My thighs use to hit the steering wheel now I hve 1.5-2 inches clearance

 

Those look like Recaro knock offs, exactly the same style seat as the original recaro LS seats like those used in Recaro TAs and many many European cars. There probably wasn't a brand here w/ a top of the line sporty model that didn't have those Recaros in them"



They're a very comfortable seat, the benchmark seat back in those days.

I was going to buy some of those, I wanted black leather ones w/ the open headrest but they were either expensive, totally shot or not leather. Didn't know about the Corbeaus.

 

these are looking great

 

I used the 93-02 style brackets and mine sit lower too. I think it's just perfect for me. I'm 6'1"

 

Tony.

 

What are those?

 

What are those?

 

glad i found this thread, can anyone tell me how you would connect a 3 point harness, like where would the other connections go, same with a 4 point. only thing i cud picture is a roll bar or the bolt hookups for the back seats. pics would also be greatly appreciated

 

Here are mine

 

Mine are a split 3 point.... the shoulder straps go back and join together into 1 connection. I run the lap seatbelts to the factory locations...bolted to the floor on either side.

The shoulder belts go up and over the roll bar cross tube and then down to the rear seats factory location for the rear belts. Using factory bolts to connect the belts to the floor. On this setup the belt rests on the rollbar cross tube so in the event of the crash it pivots from that point as if it was bolted to the roll bar. You do not want to have the shoulder belts go down to the floor immediately behind the seat. It can compress your spine in a crash.

 

can you send me the link for your seat belts, sounds like a good belt set up cause i wanted to use the 2 orig bolts and then they go through the seat and then connect to one. it sounds really good, only problem is that i dont have a rollbar, and i would still like to use the back seats, so maybe i could find another place to bolt it, could you show pics of your set up??

 

I got the scroth rallye 3, popular with the WRX crowd for awhile there. Some BMW's i heard came stock with these in some countries, not sure if in the USA or not.

http://www.schrothracing.com/store/T...allye/rallye-3

Supposively the only DOT approved harness belt...uses buckles like stock and has a DOT sticker on it. NOT NHRA legal as its not a 5 point SFI rated belt. I'm going to upgrade to matching Corbeau SFI 5 points this year.

If you dont have a roll bar you can try to bolt them to the back seats' upper mounting point for the rear belts. Thats one way to do it and still be safe as recommended by Schroth. Click on the link and at the bottom of the page they have the instructions for the belts. They have a picture of suitable mounting points you can use.

 

just checking in on this thread. some good looking seats here!

 

The project - what kind of seats are those?

 

I love these Corbeau CR1 seats ....
QUESTION, for all you 3rd Gen fans (newbie here) I have already found out these seats fit a '89' IROC, ... BUT! ...
What about the rear seats?
Does anyone know if these fit.
Do people in general do both front & rear or just the fronts?

 

ebay seats 250 shipped for the pair . there comfortable an hold you in place in a hard turn you just need to drill an tap the back hole if you use the stock sliders .theyt do set you up an inch taller .

 

I would not swap the rear

 

i barely ever use my rear seats an after i put a 6-8 point bar in there there will be no room for anyone in mine .

 

Yes these seats fit really nice. i just bolted them in today and they look amazing. I will post pictures as soon as possible. I also have corbeau 4 point harness's on both

 

Summit Racing Sport seats on modified factory brackets.

 

And those are what seats? Doesn't do us any good to know about them if we don't know what brand they are or where to get them.

 

after installing a new set of seats last summer. i am going to do it a 2nd time with a set of Recaros.

 

i said ebay search on there an you'll find them .lol