Im using dual intank 255 walbros, professional products fuel rails,a boost referenced regulator and 60 lb injectors. Unless your going forced induction you dont need much of the this. You should be able to get by with a single walbro in the tank and a regulator to get the fuel back the tank unless your swapping in an ls1 tank as well.

 

The log side is 2 1/2" pipe with 1 3/4" primaries.


heres a vid of my recent dyno run
http://vids.myspace.com/index.cfm?fu...deoID=63562643

 

Do you have any better pics of how you welded the t4 flange?

 

what do mean by "unless you're swapping in an ls1 tank"? i'm in the process of putting my ls1 tank in. I've got a racetronix pump with the hot wire harness. i dont want to have to pull the tank back out later lol i want to be set on fuel for a long while

 

Because the ls1 tank does not use a return line, its regulated at the tank. It would probably make for a cleaner install that way. And also im not sure what people are doing about the fuel gauge with that tank, it would be fine if your using an ls1 cluster because the fuel gauge on an ls1 4th gen goes from the tank to the pcm and then to the cluster, its not an ohm resistance set up like a 3rd gen. Other people may have a way around it and still using the 3rd gen gauge but I dont have experience with that myself.

 

I dont off hand but I will be taking off my whole turbo set up soon to get it ceramic coated, I can get some pics then. It took some heat and some hammering to get the pipe to merge into the t4 flange but it ended up looking pretty good.

 

any onboard videos? great work

 

Do have a pic where you tapped the pan for the turbo drain?

 

I dont have a pic, but I used an aluminum -10 male fitting that I welded near the middle of the pan above the oil level. I will try and get a pic later tonight, i had to hammer the crossmember quite a bit to get clearance.

 

I was studying your pictures and realized something. Where is your wastegate? In one picture I think I see it just under the turbo, but I'm not sure. Is it just open or a small pipe or what?

 

The wastegate is right before the turbo flange in front, then i have a dump pipe that goes down lower.

 

Here are a few pics of my hot parts that people have been asking about, hope it helps.

 

Looks sweet! Who tuned your car? How much boost you running? Im surprised you didn't get more than 512hp. But you did pretty good on TQ. What it cost to coat your hot pipes? Where'd you get it done at?

 

So i know it's been a while, but what were your final numbers with this turbo on how much psi?

 

I made 602 rwhp and 655rwtq at 12psi, without changing anything in my set up, just a better tune. But thats really leaning on it hard for a stock bottom end and I actually melted the ringland on cylinder 7. So now its a forged 370 and im going with an st80 turbo and a 4l80e.

 

What would you say a safe number on power and boost is on a stock bottom end?

 

I wasnt really concerned about longevity as this is just my weekend cruiser, but i would say 8-10 lbs should be safe on pump gas. That should put you at about 550rwhp easily depending on the tune. A set of untouched lq9's would be better, do you know what cc yours are since they've been milled?

 

Very Impressive........ JOB WELL DONE

 

over on LS1 Tech 98z28cobrakiller is getting over 1000hp on a stock crank rods with forged pistons with a truck manifold setup with the LQ4s it takes alot of air volume and fuel to make good power

Im putting my setup together now im going to go with the L92 heads GMPP intake stock bottom and hp tuners

 

Thread resurection. Man, 740rwhp and 760rwtq. That means that engine is cranking out over 800hp. And you would never know it just by looking on the outside.

 

Yea its quite a sleeper, heres a few updated pics. Its now a forged 370 with an 80mm turbo and also swaped to a 4l80e at the same time. I did this last winter. I also did a 4th gen dash 2 winters ago. This winter im doing and 8 pont cage, tubular k member and a arms and a coil over set up.

 

Heres a few more

 

heres a video at the track
http://youtu.be/lxV2UDrSZfg

 

That looks fun right there! What times did you have down the quarter when you where making 602rwhp. my camaro is going to dyno shop hopefully be the end of next week to have d1sc procharger installed, i should make around 570-680rwhp

 

When I was making that power the best I got was 11.06 but that was also with a t56.