$500!!!!

This is a complete 350 TPI engine from an 89 firebird.

The block has been bored over .030, professionally assembled, re-machined heads, magna fluxed, and valves redone. All internal compents of the engine are new with 0 miles on them (never installed). TPI induction is also included.

It has a Sealed Power Rebuild kid for a 89 350 from federal-modul. The new pistons are forged, new cam and freeze plugs.

NEW - distributor, distributor gasket, coil induction pickup, Bosch Platinum +4 plugs (pre-gapped to specification), Oil pan gasket, Dynomax Shorty Headers (no air), water outlet gasket, thermostat, crankshaft, lifters, pushrods, rocker arms, oil sending unit, and timing chain.

All the accesories are included.

I also have the complete wiring harness from the 89 TPI bird as well as the ecm.

I bought this engine with the intent of putting it in my 91 camaro, but i changed my mind and am now saving up for a LS1 swap.



Pics available apon request


EDIT:

 

how much you looking to get for it?

 

I'll shoot for 1500 or the highest reasonable price offered.

 

I'm interested in the longblock....I've got my own injection, exhaust, and accesories. If your up to selling the rest by itself on the web I could see if I could come up with $750 for the motor.

you can get up to 500 for the TPI....
if the accesories are Serpentine that's another 200 or so...
the headers are another 75-100

I'd was wondering if you had pics as well....

Thanks
Ryan

 

I'd like to sell it all at once, but if if someone else is interested in the injection i'll make an exception.

Email me for the pics.

 

still available

 

bump

 

$1300

gome get it

 

Still for sale

 

Pics available, just ask.

 

Im intrested, could you send me some pictures to enabled3k@excite.com?

also, does it have most everything needed for a swap or is there some stuff that would need to be bought?

ttyl

 

You've got mail.

 

Send me the pictures too. jeff@rummell.net

 

You have pics.

 

live in columbus ohio, how far will you drive

 

sent you an email.

 

I'll meet you half way if you cover the cost of gas. It'll be close to a 3 hour drive for both of us according to mapquest.

 

You have mail.

 

Dropping the price to $1,100 come get this out of my garage.

 

Bump

 

$950 and it's yours

 

SEND ME SOME PICS OF WHAT YOU HAVE, AND I PROLLY OVER LOOKED IT BUT THIS MOTOR IS APART RIGHT? DOES IT COME WITH THE INJECTION? AND IS ALL THE MACHINE WORK DONE? ALL I HAVE TO DO IS PUT IT TOGETHER? THANKS MY EMAIL IS JAI_NOTT@HOTMAIL.COM, I CAN NOT STRESS HOW MUCH I NEED AN ENGINE, SO GET AHOLD OF ME SOON THANKS

 

It is all in one piece, and you have mail.

 

ive been eyeing this for awhile i know u said u rather it be picked up but would u ship as well? of course id throw in an incentive 4 ya

 

I could probably find a way to ship it if the expenses were covered = ).

 

Is this complete and ready to run (aside from the computer and wiring harness)?

What cam is in it? Is it a stock cam or an aftermarket?

Please send pics to gchu@att.net

 

Would you be willing to trade?

 

Is the complete motor still for sale as of 7-7-05?

 

i am interested in it can you send some pics. michael_mciver@msn.com and also did you have the work done or did the person you bought it from say he had it done? just want to check because i bought one before and all he did was a good clean job. i got hosed for 700 bucks

 

As of 7/9/05 the motor is still for sale, I'll edit this post when I get home and am able to find the name of the shop that put it together, apon request I'll give the phone number as well.

And as for trades, I'll trade for a LT1 motor or an LT1 T-56, I'd prefer the T-56 or cash though.

 

How much shipped to 29053?

 

Around 1250 giveor take 100.

 

please email me with a complete details and a copy of the receipt from the shop that put it together. i am about 4 hours away from you but am very interested and have cash in hand.

lmk,

Dave

 

Would you sell just the wiring harness.

 

Hey, I'm interested in this motor too and I live in NJ so I could probably just pick it up. Could you email me some pictures at johnfdahl@yahoo.com ? Thanks. Just let me know if you've already sold it.
Jon

 

For those that might be interested shipping to California would cost around $250 - $300. Obviously it would cost proportionally less the closer you are to me.

 

Do you have any pictures of the inside? Or you doing the rebuild?
jon

 

Sorry guys, the engine has found a new home in my brothers car. I'll have an extra TPI intake off a 305 if anyone is still interested in that.

Edit: Plans changed again, my Father won't let my brother put a 350 in his car so the engine sale is now pending. If it falls through I'll post back.

 

Still for sale guys.

 

Please send pics of motor and info on engine builder to my email bdoz519@cs.com. Also what cam is in this motor? thanks

 

I don't know the exact details of the cam, just that it came with the federal mogul kit.

Still for sale.

 

Thanks anyways after almost 2 weeks waiting for a reply. I went and purchased a motor off of somebody else. Good luck selling your motor.

 

what's the current asking price? I want pics and info: RazorWingX7@hotmail.com

 

Sorry... I thought I had emailed you and just didn't get a responce back.

IraSummers:

You'll have the pictures by the end of the 15th.

 

Price lowered to $900. Located in central PA. I can get very reasonable shipping if desired.

 

never recived a thing from you. all I need is a short block. no wiring I don't realy even need the heads.

 

PM'd you Ira. I'd like to sell everything all at once, but I am open to suggestions.

 

TTT

 

Is this still complete and ready to run? With computer, harness, sensors, etc. Does it leak any fluids or smoke?

Can you email (gchu@att.net) the info on the builder as well as what was detailed on the reciept?

 

This is the info of the shop that put the engine together.

Eric's Machine Shop
Route 209 & Weir Lake Road
P.O. Box 732
Broadheadsville, PA 18322
(570) 402-9033

Receipt for just the block work, valve job, and assembly was $670 alone .