[OH] Vortec Ram Port (like a lowered stealthram)
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
SOLD Vortec Ram Port (like a lowered stealthram)
I just picked up this chrome plated Street & Performance Ram Port for Vortec heads. I was hoping it would be adaptable to my regular heads, but no go.
It sells for more than $3,000 new at Street and Performance. It's comparable to a Holley Stealth Ram. The height is 9.25 inches from bottom of manifold to top of throttle body. So it should fit under the Firebird hood.
Asking $800 plus shipping.
Includes the manifold, plenum, injectors, rail, TB, air filter everything you see attached.
I've had it two years, I don't think I'll ever install it.
It sells for more than $3,000 new at Street and Performance. It's comparable to a Holley Stealth Ram. The height is 9.25 inches from bottom of manifold to top of throttle body. So it should fit under the Firebird hood.
Asking $800 plus shipping.
Includes the manifold, plenum, injectors, rail, TB, air filter everything you see attached.
I've had it two years, I don't think I'll ever install it.
Last edited by JJ63; Sep 20, 2018 at 09:39 AM. Reason: SOLD
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Short Ram (like a lowered stealthram)
I also have a S&P wiring harness and 7730 ecm for this piece. Many if not all sensors are included. $100
Joined: Jun 2000
Posts: 5,364
Likes: 51
From: Enschede, Netherlands
Car: 82 TA 87 IZ L98 88 IZ LB9 88 IZ L98
Engine: 5.7TBI 5,7TPI 5.0TPI, 5,7TPI
Transmission: T5, 700R4, T5, 700R4
Axle/Gears: 3.08, 3.27, 3.45, 3.27
Vortec Short Ram (like a lowered stealthram)
Tempting. I have the same but non vortec on my supercharged stepside.
It did not fit under my iroc hood without cutting the reinforcement. It will not fit a firebird hood
It did not fit under my iroc hood without cutting the reinforcement. It will not fit a firebird hood
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Short Ram (like a lowered stealthram)
When I got home I measured it again and it's a bit under 9.25. Probably closer to 9".
So it should be low enough for f-bodies.
The S&P catalog reads that the vortec short-rams are lower profile than the regular multiport units.
http://www.hotrodlane.cc/2015catalog_pagenumbers.pdf
Page 61 for the description.
Thanks for looking.
So it should be low enough for f-bodies.
The S&P catalog reads that the vortec short-rams are lower profile than the regular multiport units.
http://www.hotrodlane.cc/2015catalog_pagenumbers.pdf
Page 61 for the description.
Thanks for looking.
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Short Ram (like a lowered stealthram)
Price Drop $800
Last edited by JJ63; Jul 31, 2018 at 09:51 AM.
Junior Member
iTrader: (3)
Joined: Feb 2009
Posts: 17
Likes: 0
From: Perkasie, PA
Car: 1988 Iroc Z28
Engine: 350
Re: Vortec Short Ram (like a lowered stealthram)
Bump for a nice intake setup good luck with the sale there are currently 5 really nice intake setups all different and no one biting on any of them
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Short Ram (like a lowered stealthram)
I know. If I didn't get this Shortram last month, I'd be all over that First unit. Actually I'm keeping my eyes open for a set of vortec heads. I might as well try out the shortram.
Trending Topics
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Ram Port (like a lowered stealthram)
More pics.
Last edited by JJ63; Jul 31, 2018 at 07:16 PM. Reason: Picture add
Joined: Oct 2001
Posts: 12,214
Likes: 1,140
From: Il
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Vortec Ram Port (like a lowered stealthram)
Pretty cool intake!
Member
iTrader: (2)
Joined: Oct 2007
Posts: 321
Likes: 18
From: Portland Or.
Car: 1992 Z28 1LE
Engine: L98
Transmission: 700R4
Axle/Gears: SLP dana 44 3.92
Re: Vortec Ram Port (like a lowered stealthram)
I have absolutely no reason to buy this, but I am trying to talk myself out of buying this from you. I would love to have that think as a shelf ornament! Such a cool period correct piece
Joined: Jun 2000
Posts: 5,364
Likes: 51
From: Enschede, Netherlands
Car: 82 TA 87 IZ L98 88 IZ LB9 88 IZ L98
Engine: 5.7TBI 5,7TPI 5.0TPI, 5,7TPI
Transmission: T5, 700R4, T5, 700R4
Axle/Gears: 3.08, 3.27, 3.45, 3.27
Re: Vortec Ram Port (like a lowered stealthram)
No
Joined: Sep 2003
Posts: 25,895
Likes: 429
From: Pittsburgh PA
Car: 89 Iroc-z
Engine: 555 BBC Turbo
Transmission: TH400
Axle/Gears: MWC 9” 3.00
Re: Vortec Ram Port (like a lowered stealthram)
2 yrs later? Surprised it didnt sell. Try ebay
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Joined: Aug 2009
Posts: 455
Likes: 26
From: London, UK
Car: 1991 Trans Am
Engine: L31, LT4 hot cam
Transmission: T5
Axle/Gears: 3:42 LSD
Re: Vortec Ram Port (like a lowered stealthram)
any new sources for information on this? Looks like Street & Performance are down to a facebook page.
Seriously looking for a vortec intake for my L31 build but would just like to educate myself on this intake
thanks
Seriously looking for a vortec intake for my L31 build but would just like to educate myself on this intake
thanks
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Ram Port (like a lowered stealthram)
I see the link I had is now dead. I don't think I saved the pdf file, but I'll look.
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Ram Port (like a lowered stealthram)
Sorry couldn't find the old catalog page. Street & performance closed a couple years ago. It should just bolt on, connect the fuel, sensors and vacuum lines. A couple holes for brake and pcv lines need to be made.
Joined: Aug 2009
Posts: 455
Likes: 26
From: London, UK
Car: 1991 Trans Am
Engine: L31, LT4 hot cam
Transmission: T5
Axle/Gears: 3:42 LSD
Re: Vortec Ram Port (like a lowered stealthram)
thanks; let me give it some thought and I'll be in touch if I want to go for this
Thread Starter
Joined: Jul 1999
Posts: 200
Likes: 3
From: Chesterland, Oh
Car: 92 Trans Am
Engine: 350 tpi
Transmission: 5 Speed
Axle/Gears: 3.42
Re: Vortec Ram Port (like a lowered stealthram)
Here is a pic of the wiring harness and ecm that is included with this intake. It's a 7730 ecm.
Junior Member
Joined: Aug 2009
Posts: 6
Likes: 0
Thread
Thread Starter
Forum
Replies
Last Post
red rock
Engine/Drivetrain/Suspension Parts for Sale
0
May 2, 2016 03:31 PM