Suspension and Chassis Questions about your suspension? Need chassis advice?

Raising the front suspension??

Thread Tools
 
Search this Thread
 
Old Sep 19, 2017 | 12:33 PM
  #1  
Drone358's Avatar
Thread Starter
Member
 
Joined: Apr 2006
Posts: 122
Likes: 0
Raising the front suspension??

I was curious if anyone has tried some rubber spacers between the lowering springs to raise the front up even a 1/2" to 1 inch is all I need. Really don't want to buy a different set.

Thanks guys
Reply
Old Sep 19, 2017 | 01:27 PM
  #2  
Tuned Performance's Avatar
Sponsor
20 Year Member
Community Builder
Community Influencer
Community Favorite
iTrader: (94)
 
Joined: Dec 2004
Posts: 16,771
Likes: 1,001
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Raising the front suspension??

Coil spring spacers seem like a dangerous idea. They would also hinder the way the spring works.
Reply
Old Sep 19, 2017 | 01:40 PM
  #3  
3rdgenmaro's Avatar
Supreme Member
20 Year Member
iTrader: (9)
 
Joined: Dec 2004
Posts: 2,042
Likes: 18
From: Lincolnton, NC
Car: 88 IROC
Engine: 97 5.7 Vortec LT4 hotcam
Transmission: 700 r4
Axle/Gears: 3.73
Re: Raising the front suspension??

Didn't these cars come factory with a rubber spring pad?

If that pad is gone in your car, you could get a set of the factory spring pads and install them. Might give you that 1/2"
Reply
Old Sep 19, 2017 | 01:42 PM
  #4  
Tuned Performance's Avatar
Sponsor
20 Year Member
Community Builder
Community Influencer
Community Favorite
iTrader: (94)
 
Joined: Dec 2004
Posts: 16,771
Likes: 1,001
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Raising the front suspension??

Pad or spacer ?
https://m.ebay.com/itm/Rubber-Coil-S...-/231879393538
Reply
Old Sep 19, 2017 | 03:13 PM
  #5  
Jaysz28's Avatar
Supreme Member
25 Year Member
Liked
Loved
Community Favorite
iTrader: (30)
 
Joined: Jul 2000
Posts: 1,519
Likes: 18
From: Fort Myers, FL
Car: 91 Firebird
Engine: 6.0
Transmission: T56
Axle/Gears: 3.73
Re: Raising the front suspension??

I've used a set of factory rear spring spacers to raise the front of 3rd gen before. The springs were cut stoopid short and I had the spacers sitting there. Seemed to ride/drive ok....
Reply
Old Sep 20, 2017 | 04:38 AM
  #6  
3rdgenmaro's Avatar
Supreme Member
20 Year Member
iTrader: (9)
 
Joined: Dec 2004
Posts: 2,042
Likes: 18
From: Lincolnton, NC
Car: 88 IROC
Engine: 97 5.7 Vortec LT4 hotcam
Transmission: 700 r4
Axle/Gears: 3.73
Re: Raising the front suspension??

Originally Posted by Tuned Performance
Im talking about the factory pad. If it has been removed, then replacing it might get the wanted 1/2".

Also, as far as spacers go, they do make other types beside the ones you posted. http://www.speedwaymotors.com/Longac...xoCjnAQAvD_BwE

But they do change the spring rate.

Last edited by 3rdgenmaro; Sep 20, 2017 at 04:43 AM.
Reply




All times are GMT -5. The time now is 05:28 PM.