Tech / General Engine Is your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!
Sponsored by:
Sponsored by: CARiD

Filter Mag???

Old Feb 3, 2007 | 04:37 PM
  #1  
TransAm12sec's Avatar
Thread Starter
Supreme Member
 
Joined: Aug 2002
Posts: 2,076
Likes: 0
From: Milwaukee, Wisconsin
Car: 1982 Trans Am
Engine: LG4
Transmission: 200C
Axle/Gears: 3:73
Filter Mag???

I haven't researched it yet, but does anyone use one? It's essentially a magnet that clamps onto the oil filter. At a minimum, I have a magnetic drain plug on all of my cars. Luckily, LSxs have that from the factory.


http://www.filtermag.com/


PDF article
http://www.filtermag.com/carcraft.pdf
Reply
Old Feb 3, 2007 | 05:30 PM
  #2  
cc 82Z-28's Avatar
Senior Member
20 Year Member
Liked
iTrader: (7)
 
Joined: May 2003
Posts: 712
Likes: 8
From: Elyria, Ohio
Car: 82 Z-28
Engine: Built 406ci
Transmission: 700R4 w/3000 stall
Axle/Gears: 3.73 Torsen Posi, Moser Axles
I use one on my daily driver and after the research I've read, it's good safe insurance, especially with a new engine start up and everyday startup, JMO. I am building a 400 for the 'maro this spring and I will use one from the very first start.
Reply
Old Feb 3, 2007 | 06:42 PM
  #3  
Gramps's Avatar
Senior Member
iTrader: (1)
 
Joined: Nov 2006
Posts: 830
Likes: 0
From: Victoria BC Canada
Car: 87 Camaro IROC
Engine: 305 TPI
Transmission: 700r4
Axle/Gears: 3.23
if your cheap and buy a poor quality filter, then its a good investment, but using a good quality filter will be just as equal, anything bigger than 25 microns will damage an engine and all the good quality ones will filter a 25 micron particle 99% of the time. and will catch a 5micron particle more than 70% of the time. poor quality ones may catch 5micron particles only 10% of the time.
Reply
Old Feb 4, 2007 | 04:38 AM
  #4  
Sonix's Avatar
Supreme Member
iTrader: (1)
 
Joined: Jul 2004
Posts: 10,763
Likes: 4
From: Calgary, AB, Canada
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
hmm, will a magnet help you attract the lead/AL/babbit chunks of bearings? I'm fairly sure it won't, since I don't *think* those are magnetic
However a cam wiping out, rockers or pushrods failing, etc, those will be held by the magnet.

I think it's worth getting either way, nifty product.

I also thought every SBC has a magnetic drain plug? Isn't that a normal part?
Reply
Old Feb 4, 2007 | 06:15 AM
  #5  
JamesC's Avatar
Moderator
25 Year Member
Liked
Loved
iTrader: (5)
 
Joined: Aug 1999
Posts: 19,282
Likes: 103
From: Lawrence, KS
Car: Met. Silver 85 IROC/Sold
Engine: 350 HO Deluxe (350ci/330hp)
Transmission: T-5 (Non-WC)
Axle/Gears: Limited Slip 3.23's
Been using one for several years. Can't hurt, might help, so why not.

JamesC
Reply
Old Feb 4, 2007 | 07:28 AM
  #6  
AsphaltAssalter's Avatar
Junior Member
 
Joined: Aug 2004
Posts: 66
Likes: 0
From: Alabama
Car: 92 Camaro
Engine: 305
Transmission: T5
Originally Posted by Sonix
I also thought every SBC has a magnetic drain plug? Isn't that a normal part?
My RS didn't come with one.
Reply
Old Feb 4, 2007 | 10:04 AM
  #7  
chesterfield's Avatar
Member
 
Joined: Feb 2005
Posts: 475
Likes: 0
From: California
Car: Pontiac
Or you can save yourself $35 and tear apart an old harddrive and slap the magnets on your oil filter. Reuse them each filter change. Hard drives use the same neodymium magnets used by filtermag. If you got a few old drives or want to spend a couplebucks at the thrift store, you can get enough for the bottom of your transmission pan too.


http://www.gadgetjq.com/oil_magnet.htm
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Cam-aro
Camaros Wanted
2
Nov 12, 2015 03:35 PM
FormulasOnly
TPI
4
Oct 2, 2015 05:52 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 09:47 AM.