This driveshaft fit my bird?
Thread Starter
Senior Member
iTrader: (2)
Joined: Dec 2007
Posts: 990
Likes: 6
From: Virginia
Car: 1992 Firebird
Engine: 350TBI
Transmission: 700r4
Axle/Gears: Ford 9in 4.10
Supreme Member
Joined: Mar 2003
Posts: 4,771
Likes: 15
From: Florida
Car: 1987 Black IROC-Z (SOLD)
Re: This driveshaft fit my bird?
Little high priced in my opinion. All Aluminum dr shafts from 3rd &4th gen cars will fit V8 cars. I would not pay over $120 for one
Joined: Aug 1999
Posts: 19,282
Likes: 103
From: Lawrence, KS
Car: Met. Silver 85 IROC/Sold
Engine: 350 HO Deluxe (350ci/330hp)
Transmission: T-5 (Non-WC)
Axle/Gears: Limited Slip 3.23's
Re: This driveshaft fit my bird?
Doesn't look right (what's the black all about). I sold, once upon a time, 70+ JG1 alum shafts for $160 including shipping. You should do better than the suggested price.
JamesC
JamesC
Joined: Mar 2000
Posts: 43,187
Likes: 46
From: Littleton, CO USA
Car: 82 Berlinetta/57 Bel Air
Engine: L92/LQ4 (both w/4" stroke)
Transmission: 4L80E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
"Stock photo".
"Remanufactured".
3-1/2" tube means earlier type. At least, the LS1 f-body take-out I got was 4" tube, and the '92 f-body take-out I got was 3-1/2" tube. Not sure exactly when the switch took place. I like the 4" tube a lot better, can't remember off the top of my head what I paid for each.
"Remanufactured".
3-1/2" tube means earlier type. At least, the LS1 f-body take-out I got was 4" tube, and the '92 f-body take-out I got was 3-1/2" tube. Not sure exactly when the switch took place. I like the 4" tube a lot better, can't remember off the top of my head what I paid for each.
Thread Starter
Senior Member
iTrader: (2)
Joined: Dec 2007
Posts: 990
Likes: 6
From: Virginia
Car: 1992 Firebird
Engine: 350TBI
Transmission: 700r4
Axle/Gears: Ford 9in 4.10
Re: This driveshaft fit my bird?
Alright thanks guys, ill just search around and look for the 4in one!
Joined: Aug 2006
Posts: 12,813
Likes: 110
From: Central NJ
Car: 86 Trans Am
Engine: 408 stroker sbc
Transmission: TKO600
Axle/Gears: Moser full floater m9, 3:70 trutrac
Re: This driveshaft fit my bird?
wait, what? the stock ls1 shaft diameter is 3" is it not? how the heck would you fit a 4" ds in there?
i bough an aftermarket 3.5" ds and its a tight squeeze and i kinda regret doing it.
i bough an aftermarket 3.5" ds and its a tight squeeze and i kinda regret doing it.
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
Apr 25, 2016 09:21 PM
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
1
Nov 19, 2015 07:03 AM
Eric2ndGen
Transmissions and Drivetrain
0
Aug 31, 2015 12:33 AM