I got the numbers off my rear end, now where to find..

Reply Subscribe

Thread Tools

Search this Thread

Apr 30, 2001 | 11:52 AM

ScreaminDeamin85Z

Thread Starter

Senior Member

Joined: Feb 2000

Posts: 536

Likes: 0

From: College Station/Spring, TX

I got the numbers off my rear end, now where to find..

i got the numbers off my rear end but now where do i go on the net to find what ratio i have?

------------------
Brandon
"ScreaminDeamin 360"
350 60 over, TRW forged 9.83:1 pistons,Hooker Comp headers, crane cam 216/228 .484/.512, crane 1.6 RR's, ported plenum, home made ram air, 24lb SVO injectors, crane AFPR, all going through 3 inch mandrel pipe and a flowmaster.
New project-89 IROC-Jamex Springs...and thats just about it till summer!
Soon- 6 speed, Pro 5.0 shifter and 4.10's
http://users.argolink.net/bvana

http://ScreaminDeamin.cz28.com

Apr 30, 2001 | 02:15 PM

TomP

Supreme Member

Joined: Mar 2000

Posts: 13,414

Likes: 6

From: Central NJ, USA

Car: 1986 Firebird

Engine: 2.8 V6

Transmission: 700R4

I don't think it's on the internet... my Haynes 82-92 manual lists "most" of the codes for all the years. '82-'84 is in the regular "rear axle/suspension" section, '85-'92 is in the very last chapter, "Supplemental for '85-up cars".

Then again, Haynes didn't list the code for the 3.73/posi/disc axle that I put into my car... go figure.

------------------
-Tom P (Hot rodded 1986 Firebird 2.8l) from http://www.f-body.net/mailbag/3rd/3rd_mailbag.html message boards
---Think your car could be pic of the week? Visit http://www.f-body.net for details!

Apr 30, 2001 | 07:20 PM

zenish

Supreme Member

Joined: Dec 2000

Posts: 1,271

Likes: 1

From: stallings,n.c.

Car: 1989 camaro rs convertable

Engine: 305 tbi

Transmission: 700r4

Axle/Gears: 7.5"3.42 gears forth gen 2000 camar

post the numbers

Apr 30, 2001 | 07:43 PM

ScreaminDeamin85Z

Thread Starter

Senior Member

Joined: Feb 2000

Posts: 536

Likes: 0

From: College Station/Spring, TX

ok these are the numbers i got off the rear end just above the driveshaft.
22522676

------------------
Brandon
"ScreaminDeamin 360"
350 60 over, TRW forged 9.83:1 pistons,Hooker Comp headers, crane cam 216/228 .484/.512, crane 1.6 RR's, ported plenum, home made ram air, 24lb SVO injectors, crane AFPR, all going through 3 inch mandrel pipe and a flowmaster.
New project-89 IROC-Jamex Springs...and thats just about it till summer!
Soon- 6 speed, Pro 5.0 shifter and 4.10's
http://users.argolink.net/bvana

http://ScreaminDeamin.cz28.com

Apr 30, 2001 | 09:46 PM

Petes 84Z28

Supreme Member

Joined: Jul 1999

Posts: 1,593

Likes: 3

From: out of my mind; be back in 5 minutes....

Car: 1989 Firebird Formula

Engine: Internal Combustion

Transmission: Completed

Axle/Gears: ones that turn.

Look on the forward part of the passenger side axle tube...stamped into it will be a sequence of numbers and letters like this: 2KG C343 2. Post up the first three digits, and someone can tell what the original ratio was in the rear end; in this case - 2KG equals a 3.08 open axle.

Pete

------------------
Pete's Place
HiOutput Tech Page
83 SC
originally a V6...now
206+k mile LG4/5-speed
14.935@94.14