Third Generation F-Body Message Boards
0 2019/06/01 06:53:38
0 2019/06/01 06:53:44
0 2019/06/01 06:53:49
0 2019/06/01 06:54:55
0 2019/06/01 06:54:56
0 2019/06/01 06:55:22
0 2019/06/01 06:55:24
0 2019/06/01 06:55:25
0 2019/11/11 05:53:47
0 2020/04/22 12:24:10
0 2020/04/22 12:24:11
0 2020/04/22 12:25:12
0 2020/05/28 03:06:44
0 2020/05/28 03:06:45
0 2020/05/28 03:06:47
0 2020/05/28 03:06:48
0 2020/10/19 10:38:53
0 2020/10/19 10:38:56
0 2021/08/11 12:15:37
0 2021/09/27 09:04:58
0 2021/11/28 02:25:29
0 2021/11/28 02:25:30
0 2022/03/01 12:02:00
0 2022/03/01 12:02:02
0 2022/03/01 12:06:01
0 2022/04/08 22:44:39
Finally done.
Finally done.
0 2022/06/02 06:22:02
Nearly complete assembled, the frostbite radiator fits nice in it!
Nearly complete assembled, the frostbite radiator fits nice in it!
0 2022/06/02 06:22:03
Before putting it in the car.
Before putting it in the car.
0 2022/06/02 06:22:05
So back in the car
So back in the car
0 2022/06/02 06:22:06
Measured the pushord length and installed roller rocker arms from comp cams. Theyre quite loud, need to figure out that.
Measured the pushord length and installed roller rocker arms from comp cams. Theyre quite loud, need to figure out that.
0 2022/06/02 06:22:07
The piston have enough clearance during rotating, thanks to the mild cam. Maybe I should have gone up a notch in duration on that cam but however, nothing is impossible later on.
The piston have enough clearance during rotating, thanks to the mild cam. Maybe I should have gone up a notch in duration on that cam but however, nothing is impossible later on.
0 2022/06/02 06:22:08
Put the heads on and begin to make the "check-work"
Put the heads on and begin to make the "check-work"
0 2022/06/02 06:22:09
Layed the head gasket on top and marked where the blank surface shines through to ensure nothing is rusting after building.
Layed the head gasket on top and marked where the blank surface shines through to ensure nothing is rusting after building.
0 2022/06/02 06:22:11
Assembled the engine from the bottom to top and began to put some paint on it.
Assembled the engine from the bottom to top and began to put some paint on it.
0 2022/06/02 06:22:12
So back to work B-)
So back to work B-)
0 2022/06/02 06:22:13
That how I picked up the block from my engine builder. They did a great job and correctly adjusted my camshaft SLP 51002
That how I picked up the block from my engine builder. They did a great job and correctly adjusted my camshaft SLP 51002
0 2022/06/02 06:22:14
0 2022/11/16 11:57:41
0 2022/11/16 11:57:42
0 2022/11/16 11:57:43