Third Generation F-Body Message Boards
HVAC box reinstalled on the firewall. I also reloomed the wiring harnesses in the engine bay.
HVAC box reinstalled on the firewall. I also reloomed the wiring harnesses in the engine bay.
0 2025/06/06 23:40:26
4th gen fuel tank bulkhead connector that will be replacing the 3rd gen connector for the fuel tank upgrade. I want a fully functional 4th gen setup. Evap system along with the fuel tank pressure sensor to go along with the 0411 ecm.
4th gen fuel tank bulkhead connector that will be replacing the 3rd gen connector for the fuel tank upgrade. I want a fully functional 4th gen setup. Evap system along with the fuel tank pressure sensor to go along with the 0411 ecm.
0 2025/06/06 23:40:30
New 255lph pump installed into the fuel bucket along with a new 0-90 ohm sender card.
New 255lph pump installed into the fuel bucket along with a new 0-90 ohm sender card.
0 2025/06/06 23:40:32
Racetronix fuel pump hot wire kit and tank ready to be installed.
Racetronix fuel pump hot wire kit and tank ready to be installed.
0 2025/06/06 23:40:35
0 2025/08/26 05:17:41
0 2025/12/02 21:24:18
0 2025/12/02 21:24:19
Parallel condenser with the expanding strip foam from HD installed along with the radiator.
Parallel condenser with the expanding strip foam from HD installed along with the radiator.
0 2026/04/17 21:05:20
Factory power steering cooler cleaned up and painted with sem paint.
Factory power steering cooler cleaned up and painted with sem paint.
0 2026/04/17 21:05:23
Hardware for the powering steering cooler also painted.
Hardware for the powering steering cooler also painted.
0 2026/04/17 21:05:27
TDS bar, sway bar, and pro forge steering components installed.
TDS bar, sway bar, and pro forge steering components installed.
0 2026/04/17 21:05:30
0 2026/04/17 21:05:33
New condenser and old radiator installed. I used the expanding foam strip that you can get from HD to seal in between the two.
New condenser and old radiator installed. I used the expanding foam strip that you can get from HD to seal in between the two.
0 2026/04/17 21:15:10
Factory power steering cooler cleaned and painted.
Factory power steering cooler cleaned and painted.
0 2026/04/17 21:15:13
Hardware for the power steering cooler.
Hardware for the power steering cooler.
0 2026/04/17 21:15:16
Bumper upper mounting bracket painted with sem trim black.
Bumper upper mounting bracket painted with sem trim black.
0 2026/04/17 21:15:18
Bump stops mounts for the hood painted as well.
Bump stops mounts for the hood painted as well.
0 2026/04/17 21:15:20
Had the original sway bar powder coated and installed the steering linkage parts.
Had the original sway bar powder coated and installed the steering linkage parts.
0 2026/04/17 21:15:23
What a pain in the butt to install the springs. Ended up removing the control arms and using it in the equation to compress the springs. Reinstalled the control arms with springs not fully seated in the pocket of the cross member. A ratchet strap attached to a coil and to a point on the opposite side of the cross member for the seated correctly.
What a pain in the butt to install the springs. Ended up removing the control arms and using it in the equation to compress the springs. Reinstalled the control arms with springs not fully seated in the pocket of the cross member. A ratchet strap attached to a coil and to a point on the opposite side of the cross member for the seated correctly.
0 2026/04/17 21:15:27