Third Generation F-Body Message Boards
The seatbelt plastic needs to be trimmed to seat properly.
The seatbelt plastic needs to be trimmed to seat properly.
0 2015/09/20 16:10:47
A LOOK at the seat belt mod. The bracket needs to be bent upwards to about a 45 degree angle.
A LOOK at the seat belt mod. The bracket needs to be bent upwards to about a 45 degree angle.
0 2015/09/20 16:10:33
The seats are manual with air.
The seats are manual with air.
0 2015/09/20 15:57:26
A view of the back seat. Notice it dose not match. I will get a matching one later.
A view of the back seat. Notice it dose not match. I will get a matching one later.
0 2015/09/20 15:56:47
The console is not screwed in becuse I still have a little wiring to do
The console is not screwed in becuse I still have a little wiring to do
0 2015/09/20 15:56:17
A view of the interior
A view of the interior
0 2015/09/20 15:55:54
How I cut the plastic kick panel
How I cut the plastic kick panel
0 2015/09/20 15:55:07
A close look at the bracket
A close look at the bracket
0 2015/09/20 15:54:56
Here is the front passenger kick panel. I had to cut it to fit where the ls1 bracket is mounted to the car
Here is the front passenger kick panel. I had to cut it to fit where the ls1 bracket is mounted to the car
0 2015/09/20 15:54:28
4th gen carpet fits nicely
4th gen carpet fits nicely
0 2015/09/20 15:39:34
The components of a 99 LS1 exhaust system.
The components of a 99 LS1 exhaust system.
0 2015/08/29 16:15:44
Here you can see clerance is also an issue at the rear of the cat on the drivers side.
Here you can see clerance is also an issue at the rear of the cat on the drivers side.
0 2015/08/29 16:15:12
You can see clearly her the o2 sensor opening which will have to be relocated due to hitting the k member. A SMALLER o2 from an aftermarket manifacturer might fit.
You can see clearly her the o2 sensor opening which will have to be relocated due to hitting the k member. A SMALLER o2 from an aftermarket manifacturer might fit.
0 2015/08/29 16:14:39
Another shot of the drivers cat. Close but no cigar.
Another shot of the drivers cat. Close but no cigar.
0 2015/08/29 16:12:56
Drivers side cat is located on a 99 model up close to the manifold causing clearence issues. you can see here however it almost will fit.
Drivers side cat is located on a 99 model up close to the manifold causing clearence issues. you can see here however it almost will fit.
0 2015/08/29 16:12:09
Pass side o2 sensor clears. (drivers side dose not!)
Pass side o2 sensor clears. (drivers side dose not!)
0 2015/08/29 16:11:13
Another shot of the two systems comming togeather.
Another shot of the two systems comming togeather.
0 2015/08/29 16:10:21
The y pipe will come togeather with the exzisting flow master system perfectly.
The y pipe will come togeather with the exzisting flow master system perfectly.
0 2015/08/29 16:09:53
Clearance on lower pass tube.
Clearance on lower pass tube.
0 2015/08/29 16:09:30
you can see hee the pass side exhaust is tight but will fit wothout much modification. I got it to sit corectly with no problem.
you can see hee the pass side exhaust is tight but will fit wothout much modification. I got it to sit corectly with no problem.
0 2015/08/29 16:08:45
smog pump electrical connection. I needed to be sure the stock pump comector could reach this location. The hose in photo has not been routed to air box yet.
smog pump electrical connection. I needed to be sure the stock pump comector could reach this location. The hose in photo has not been routed to air box yet.
0 2015/08/29 16:00:51
Here you can see the orientation. Notice the ai dam lower right.
Here you can see the orientation. Notice the ai dam lower right.
0 2015/08/29 16:00:19
My LS1 smog pump location.
My LS1 smog pump location.
0 2015/08/29 15:59:56
Stock LS1 instllation
Stock LS1 instllation
0 2015/08/29 15:59:24
Lots still to be done but i'm making progress.
Lots still to be done but i'm making progress.
0 2015/08/29 15:57:01
A side view of the progress
A side view of the progress
0 2015/08/29 15:56:30
0 2015/08/29 15:34:46
0 2015/08/29 15:34:06
0 2015/08/29 15:33:35
0 2015/08/29 15:33:03
0 2015/08/29 15:32:35
0 2015/08/29 15:31:50
0 2015/08/29 15:29:27
Another view of the intake. It all fit together like a glove. I just need to drill a hole for one sensor in the air filter housing.
Another view of the intake. It all fit together like a glove. I just need to drill a hole for one sensor in the air filter housing.
0 2015/08/16 00:56:09
Moving right along, I am using the stock 91 z28 air filter to pass BAR. I am told an 04 GTO Intake would also pass but this was free.
Moving right along, I am using the stock 91 z28 air filter to pass BAR. I am told an 04 GTO Intake would also pass but this was free.
0 2015/08/16 00:55:49
I wanted to see what needed to be done to get the cats to fit. No, they will not bolt right up as some would have you believe.
I wanted to see what needed to be done to get the cats to fit. No, they will not bolt right up as some would have you believe.
0 2015/08/16 00:51:44
A mock up of the cat.
A mock up of the cat.
0 2015/08/16 00:51:22
My son trying to help. Dad was that an 18 or 19"?
My son trying to help. Dad was that an 18 or 19"?
0 2015/08/16 00:49:31
My son trying to help. "Dad was that an 18 or 19"?
My son trying to help. "Dad was that an 18 or 19"?
0 2015/08/16 00:46:20
This mock up was to see what needed to be done to get the cats to fit. No, they will not bolt up as some would have you believe.
This mock up was to see what needed to be done to get the cats to fit. No, they will not bolt up as some would have you believe.
0 2015/08/16 00:45:59