Third Generation F-Body Message Boards
0 2021/09/24 16:45:02
Top view of BCA-4W connector with harness grounds and pump grounds tied in on bottom side
Top view of BCA-4W connector with harness grounds and pump grounds tied in on bottom side
0 2022/02/16 20:44:00
Back view
Back view
0 2022/02/16 20:44:10
Side showing orientation of 4 way and in-tank harness with pump ground. connector and in-tank harness match up with each other
Side showing orientation of 4 way and in-tank harness with pump ground. connector and in-tank harness match up with each other
0 2022/02/16 20:44:19
ground loops to supply power to each pump separately. Or use a hobbs switch
ground loops to supply power to each pump separately. Or use a hobbs switch
0 2022/02/16 20:44:27
Fuses new and not popped
Fuses new and not popped
0 2022/02/16 20:44:39
Solid battery connection also have that thin ground wire grounded on the coil brackets
Solid battery connection also have that thin ground wire grounded on the coil brackets
0 2022/02/16 20:44:45
Power at the grey wire thru the Rx harness at the round 7 position connector. Power was also the same reading directly from the trigger wire off the Holley harness KOEO
Power at the grey wire thru the Rx harness at the round 7 position connector. Power was also the same reading directly from the trigger wire off the Holley harness KOEO
0 2022/02/16 20:45:01
Hit all connections with a multimeter, no power at Red or Blue which is power for pumps.
Hit all connections with a multimeter, no power at Red or Blue which is power for pumps.
0 2022/02/16 20:45:10
This is what I see going thru that purple wire KOEO
This is what I see going thru that purple wire KOEO
0 2022/02/16 20:45:19
0 2022/04/08 15:17:29
0 2022/04/08 15:20:34
Just dropped center section into the housing. Still needed to do brake lines at this point.
Just dropped center section into the housing. Still needed to do brake lines at this point.
0 2022/11/01 23:36:34
Got it slid under the car and lifted onto my floor jack. Nice and flat on the bottom made it easy to lift level-ish.
Got it slid under the car and lifted onto my floor jack. Nice and flat on the bottom made it easy to lift level-ish.
0 2022/11/01 23:36:54
Shot of the torque arm clearance after I got it bolted in and onto jack stands. Centered up nicely
Shot of the torque arm clearance after I got it bolted in and onto jack stands. Centered up nicely
0 2022/11/01 23:37:00
Another shot of the torque arm and chromoly driveshaft
Another shot of the torque arm and chromoly driveshaft
0 2022/11/01 23:37:06
On car adjustable panhard bar. Founders performance
On car adjustable panhard bar. Founders performance
0 2022/11/01 23:37:11
New shoes for to put it to the ground. 275/40-17
New shoes for to put it to the ground. 275/40-17
0 2022/11/01 23:37:15
0 2022/11/02 00:02:03
0 2022/11/02 00:02:10
0 2022/11/02 00:02:15
0 2022/11/02 00:02:20
0 2022/11/02 00:02:26
0 2022/11/02 00:02:32
0 2022/11/02 00:02:38
0 2022/11/02 00:02:43
0 2023/11/06 17:44:03
0 2023/12/06 08:01:07
0 2024/02/16 15:50:32
0 2024/02/16 15:50:51
0 2024/02/16 15:51:00
New radiator and fan combo looking mint!
New radiator and fan combo looking mint!
0 2024/05/22 19:08:54
Turbo blanket from Black Sheep Industries keeps the heat in that turbo!
Turbo blanket from Black Sheep Industries keeps the heat in that turbo!
0 2024/05/22 19:09:42
Added some UMI caster/camber plates
Added some UMI caster/camber plates
0 2024/05/22 19:09:53
Thirsty girl drinking that 94. But I'm now on 91 and spraying 1000cc 50/50 water/meth
Thirsty girl drinking that 94. But I'm now on 91 and spraying 1000cc 50/50 water/meth
0 2024/05/22 19:10:02
New alternator ad244 and ICT Billet bracket. The motion raceworks 3.5" pulley was too big at idle I'm now using a Hawks 2.85" pulley.
New alternator ad244 and ICT Billet bracket. The motion raceworks 3.5" pulley was too big at idle I'm now using a Hawks 2.85" pulley.
0 2024/05/22 19:10:15
Had the manifolds, turbine housing and turbo mount ceramic coated in Cerakote glacier black.
Had the manifolds, turbine housing and turbo mount ceramic coated in Cerakote glacier black.
0 2024/05/22 19:10:35
Driver side of things
Driver side of things
0 2024/05/22 19:10:50
Shortened the Hooker crossover by cutting flanges off and gluing new ones on. Pretty simple. Added a Moroso deep pan for my 4L80e.
Shortened the Hooker crossover by cutting flanges off and gluing new ones on. Pretty simple. Added a Moroso deep pan for my 4L80e.
0 2024/05/22 19:11:12
Moved intercooler into this spot because it's what I should have done the first time around.
Moved intercooler into this spot because it's what I should have done the first time around.
0 2024/05/22 19:11:27