Third Generation F-Body Message Boards
Heat with this setup has been a little difficult to deal with. Found this melted when I pulled everything to get coated
Heat with this setup has been a little difficult to deal with. Found this melted when I pulled everything to get coated
0 2024/05/22 19:32:10
New inserts installed. Still have another set which I may take to a machine shop to have them make out of aluminum
New inserts installed. Still have another set which I may take to a machine shop to have them make out of aluminum
0 2024/05/22 19:32:25
I got torque management working beautifully on my Dominator ecu. Anything that will make my expensive transmission last longer I'm all for it.
I got torque management working beautifully on my Dominator ecu. Anything that will make my expensive transmission last longer I'm all for it.
0 2024/05/22 19:32:37
One of many tables used for torque management. This is the timing offset based off fuel flow and trans slip. I'm really starting to take advantage of the endless possibilities the Holley is capable of!!
One of many tables used for torque management. This is the timing offset based off fuel flow and trans slip. I'm really starting to take advantage of the endless possibilities the Holley is capable of!!
0 2024/05/22 19:32:46
0 2024/05/25 14:35:11
0 2024/05/25 14:35:44
I'm thinking of making a cover to go over that huge gap so everything is hidden
I'm thinking of making a cover to go over that huge gap so everything is hidden
0 2024/05/25 14:35:59
I want to change the intake piping and be gone of those silicone couplers using the motion raceworks setup
I want to change the intake piping and be gone of those silicone couplers using the motion raceworks setup
0 2024/05/31 15:27:36
0 2024/11/01 15:32:46
0 2024/11/01 15:32:53
0 2024/11/01 15:32:57
0 2024/11/01 15:33:02
0 2024/11/01 15:33:09
Making a new charge pipe that will go into the throttle body. I was having an issue with the silicone couplers not holding past 16/17 psi and the pipe would blow off
Making a new charge pipe that will go into the throttle body. I was having an issue with the silicone couplers not holding past 16/17 psi and the pipe would blow off
0 2024/11/01 15:33:16
There's a weld flange that isn't pictured here but after I get this all welded up I'll get it coated as well
There's a weld flange that isn't pictured here but after I get this all welded up I'll get it coated as well
0 2024/11/01 15:33:23
0 2024/11/06 22:41:06
This is how your battery should look on the datalog. The green line up top
This is how your battery should look on the datalog. The green line up top
0 2024/11/29 14:58:45
This is yours in yellow at the top. See the difference??
This is yours in yellow at the top. See the difference??
0 2024/11/29 14:59:43
0 2025/01/05 21:34:01
0 2025/04/25 11:40:08
Mounted using aluminum flat bar and bolted to the radiator. The fan ECM is at the bottom where it's not as hot
Mounted using aluminum flat bar and bolted to the radiator. The fan ECM is at the bottom where it's not as hot
0 2025/04/25 11:40:33
0 2025/05/02 12:55:44
Side by side pic of the Lexan and glass tops. Night and day difference
Side by side pic of the Lexan and glass tops. Night and day difference
0 2025/05/26 18:04:09
Even tho my paint sucks and needs to get done I can't get over how much better these glass tops look. Finally able to see clearly out of them too is awesome
Even tho my paint sucks and needs to get done I can't get over how much better these glass tops look. Finally able to see clearly out of them too is awesome
0 2025/05/26 18:04:53
These are the 0-2" lowered coilovers with thrust bearing kit with spanner wrenches and they clear my larger rear sway bar no problem
These are the 0-2" lowered coilovers with thrust bearing kit with spanner wrenches and they clear my larger rear sway bar no problem
0 2025/05/26 21:26:08
0 2025/06/02 21:37:39
0 2025/06/12 11:04:52
0 2025/06/12 11:05:13
0 2025/06/12 11:05:33
0 2025/06/12 11:05:51
0 2025/06/27 20:44:17
These units are set up for ground trigger but can be used for +12v trigger as well
These units are set up for ground trigger but can be used for +12v trigger as well
0 2025/06/29 18:06:45
Something like this. The crossmember is welded to the SFC's and is bolted in the center with the front of the TA on a 5 position mount. Midwest calls this a "mid-length" TA
Something like this. The crossmember is welded to the SFC's and is bolted in the center with the front of the TA on a 5 position mount. Midwest calls this a "mid-length" TA
0 2025/11/14 05:34:18
0 2025/11/19 08:10:39
0 2025/11/19 08:11:01
0 2025/11/19 08:12:27
0 2025/12/23 17:50:19
0 2026/01/25 13:44:00
0 2026/02/03 09:55:56
This was P 3, I 4.5, D 0
This was P 3, I 4.5, D 0
0 2026/03/18 07:26:12