Third Generation F-Body Message Boards
Location of shifter without plate removed
Location of shifter without plate removed
0 2025/04/18 19:00:38
Need about a 4" offset from location where it comes through tunnel
Need about a 4" offset from location where it comes through tunnel
0 2025/04/18 18:59:20
With driveshaft in. Had to shorten the stock driveshaft by about 1/2" to allow it to be put in. Local shop did it for around $120.
With driveshaft in. Had to shorten the stock driveshaft by about 1/2" to allow it to be put in. Local shop did it for around $120.
0 2025/02/09 10:09:25
More angles.
More angles.
0 2025/02/09 10:09:23
Y-Pipe in you can see still is the lowest point. I do want to re-do that to prevent scraping.
Y-Pipe in you can see still is the lowest point. I do want to re-do that to prevent scraping.
0 2025/02/09 10:09:21
Transmission up and mounted
Transmission up and mounted
0 2025/02/09 10:09:19
Shifter location.
Shifter location.
0 2024/12/08 18:12:03
Shifter in relation to auto shifter bezel
Shifter in relation to auto shifter bezel
0 2024/12/08 18:12:00
Shifter temporarily installed to see fitment with plastics.
Shifter temporarily installed to see fitment with plastics.
0 2024/12/08 18:08:24
Opening is almost complete and you can see the shifter mount.
Opening is almost complete and you can see the shifter mount.
0 2024/12/08 18:08:21
You can see through the shifter grommet hole the top left corner of the shifter mount. That is where I started cutting with the body saw and making small cuts.
You can see through the shifter grommet hole the top left corner of the shifter mount. That is where I started cutting with the body saw and making small cuts.
0 2024/12/08 18:08:17
Need to drill out the spot welds for the auto shifter mount.
Need to drill out the spot welds for the auto shifter mount.
0 2024/12/08 18:07:30
You can see in this picture that the mount is actually in front of the cross member. I ended up welding a square tube piece on the front side to get it to mount. I will upload pictures later.
You can see in this picture that the mount is actually in front of the cross member. I ended up welding a square tube piece on the front side to get it to mount. I will upload pictures later.
0 2024/12/08 18:04:47
Transmission with bellhousing installed
Transmission with bellhousing installed
0 2024/12/08 17:56:49
Adapter Kit
Adapter Kit
0 2024/12/08 17:55:15
0 2024/12/08 17:54:47
0 2024/12/08 17:54:36
0 2024/12/08 17:54:33
0 2024/12/08 17:54:30
0 2024/12/08 17:54:27
0 2024/12/08 17:54:23
0 2024/07/04 08:25:51
0 2024/07/04 08:25:49
0 2024/07/04 08:25:47
0 2024/07/04 08:25:45
0 2024/07/04 08:25:43
0 2022/04/22 17:41:05
0 2022/04/22 17:40:39
0 2022/04/22 17:39:52
Overall shot of the engine bay in the state to get it running. I plan on getting rid of the big inlet pipe and use the stock air box. Before I pull the engine out I am going to wrap wiring and loom it all to clean it up.
Overall shot of the engine bay in the state to get it running. I plan on getting rid of the big inlet pipe and use the stock air box. Before I pull the engine out I am going to wrap wiring and loom it all to clean it up.
0 2022/04/20 18:18:57
Powersteering line I had made at my local hydraulic line for $40. I specified -8 JIC fittings which will work with the -8an fittings on the steering box and the power steering pump
Powersteering line I had made at my local hydraulic line for $40. I specified -8 JIC fittings which will work with the -8an fittings on the steering box and the power steering pump
0 2022/04/20 18:16:28
Power steering line. You can see the hard line that has -8an fitting coming from the top of the power steering pump. This is holley part No. 198-202.
Power steering line. You can see the hard line that has -8an fitting coming from the top of the power steering pump. This is holley part No. 198-202.
0 2022/04/20 18:11:43
Stock 4th gen ls1 camaro upper radiator hose fits perfectly.
Stock 4th gen ls1 camaro upper radiator hose fits perfectly.
0 2022/04/20 18:10:11
Lower radiator hose was a modified 2.8 v6 3rd gen camaro hose that was shortened.
Lower radiator hose was a modified 2.8 v6 3rd gen camaro hose that was shortened.
0 2022/04/20 18:08:22
Accessory set up with Holley kit. Power steering pump was a GM saginaw type II. Using a camaro ls1 waterpump.
Accessory set up with Holley kit. Power steering pump was a GM saginaw type II. Using a camaro ls1 waterpump.
0 2022/04/20 18:06:36
0 2022/04/20 17:43:16
Passenger side manifold
Passenger side manifold
0 2022/04/02 15:19:30
Driver side manifold
Driver side manifold
0 2022/04/02 15:18:10
Overall shape and routing. You can see the down pipes for either side are because of how different the truck manifolds exit. I also flattened the center section to help with clearance.
Overall shape and routing. You can see the down pipes for either side are because of how different the truck manifolds exit. I also flattened the center section to help with clearance.
0 2022/04/02 15:01:37
Here you can see how low it hangs. It isn't perfect since it still hangs about 1.5" below k-member but I am happy with it.
Here you can see how low it hangs. It isn't perfect since it still hangs about 1.5" below k-member but I am happy with it.
0 2022/04/02 15:00:09