Third Generation F-Body Message Boards
Outlet of Y-pipe falls perfectly in stock location. Still have to make sure that tires fit but I don't see a problem here.
Outlet of Y-pipe falls perfectly in stock location. Still have to make sure that tires fit but I don't see a problem here.
0 2022/04/02 14:59:02
Backside of passenger downpipe where Passenger side O2 sensor will be located
Backside of passenger downpipe where Passenger side O2 sensor will be located
0 2022/04/02 14:57:34
Where passenger side down pipe meets crossover pipe. More than enough clearance around everything.
Where passenger side down pipe meets crossover pipe. More than enough clearance around everything.
0 2022/04/02 14:53:46
Driver's side underneath. This is where I located the O2 sensor since flipping into the back side there would not have been any room. This has more than enough room to get a wrench on it and tighten it.
Driver's side underneath. This is where I located the O2 sensor since flipping into the back side there would not have been any room. This has more than enough room to get a wrench on it and tighten it.
0 2022/04/02 14:51:41
Driver side manifold to y-pipe. This one went more straight down but the merge in the manifold still makes the clamp pretty close to the firewall. I am going to watch this one to see if it ends up hitting.
Driver side manifold to y-pipe. This one went more straight down but the merge in the manifold still makes the clamp pretty close to the firewall. I am going to watch this one to see if it ends up hitting.
0 2022/04/02 14:47:03
Passenger side manifold to y-pipe. I will probably end up re-routing power wires since it is a little close for comfort. you can see an almost 90 turn down is required on this side.
Passenger side manifold to y-pipe. I will probably end up re-routing power wires since it is a little close for comfort. you can see an almost 90 turn down is required on this side.
0 2022/04/02 14:45:23
0 2022/02/07 18:13:20
0 2022/02/07 18:13:04
0 2022/02/07 18:06:53
0 2022/02/07 18:06:36
0 2022/01/12 16:01:07
0 2022/01/12 16:01:00
0 2022/01/12 16:00:48
0 2022/01/12 16:00:41
0 2022/01/12 16:00:33
0 2022/01/12 16:00:26
0 2022/01/12 16:00:18
0 2022/01/12 16:00:11
0 2021/12/23 19:28:27
0 2021/12/23 19:28:06
0 2021/12/23 19:27:14
0 2021/12/23 19:26:49
installed on the engine with DBW throttle body
installed on the engine with DBW throttle body
0 2021/12/16 17:28:23
Complete LS6 intake
Complete LS6 intake
0 2021/12/16 17:27:58
0 2021/12/16 17:20:11
Profile is flipped for 3rd gen and 4th gen torque arms.
Profile is flipped for 3rd gen and 4th gen torque arms.
0 2021/12/16 17:18:32
Torque arm comes past the mount from where it would be on the 700r4.
Torque arm comes past the mount from where it would be on the 700r4.
0 2021/12/16 17:17:43
0 2021/11/27 18:33:22
Still good clearance at top of transmission to transmission tunnel
Still good clearance at top of transmission to transmission tunnel
0 2021/11/27 18:33:15
0 2021/11/27 18:33:09
2 piece crossmember assembled.
2 piece crossmember assembled.
0 2021/11/27 18:32:30
Drilled new hole about 1/2" further back on the crossmember the main crossmember.
Drilled new hole about 1/2" further back on the crossmember the main crossmember.
0 2021/11/27 18:31:49
Drilled new holes about 1/2" further back on the crossmember that bolts to the body.
Drilled new holes about 1/2" further back on the crossmember that bolts to the body.
0 2021/11/27 08:01:29
transmission with F-body Tailshaft installed. I didn't notice until I tried but the torque arm mount from the 700r4 will not fit on the 4l60e. Need to source one of those now.
transmission with F-body Tailshaft installed. I didn't notice until I tried but the torque arm mount from the 700r4 will not fit on the 4l60e. Need to source one of those now.
0 2021/11/24 18:57:19
New F-body tailshaft housing bought on Summit for $80 is the exact same length as the 2wd pickup one so it was a direct swap.
New F-body tailshaft housing bought on Summit for $80 is the exact same length as the 2wd pickup one so it was a direct swap.
0 2021/11/24 18:57:13
Transmission mount on 4L60E's sit too far back and the cross member needs to be modified.
Transmission mount on 4L60E's sit too far back and the cross member needs to be modified.
0 2021/11/24 18:57:06
200K M30 2wd 4l60E from chevy 1500
200K M30 2wd 4l60E from chevy 1500
0 2021/11/24 18:57:00
Clearance to the driver side head and firewall
Clearance to the driver side head and firewall
0 2021/11/24 18:40:41
Clearance to the passenger side head and firewall
Clearance to the passenger side head and firewall
0 2021/11/24 18:40:35
0 2021/11/24 18:38:14