Third Generation F-Body Message Boards
0 2015/07/13 21:33:01
0 2015/07/13 21:32:58
Tada. Took a while but came out great. Little primer and repaint of the engine bay, never know it was in distress.
Tada. Took a while but came out great. Little primer and repaint of the engine bay, never know it was in distress.
0 2015/07/08 14:53:59
place the top back on, weld it up solid and POR 15 that to seal it.
place the top back on, weld it up solid and POR 15 that to seal it.
0 2015/07/08 14:53:57
Once your done, POR 15 the entire well so seal it
Once your done, POR 15 the entire well so seal it
0 2015/07/08 14:53:56
Lay it in place and weld up the seams; like it was never gone
Lay it in place and weld up the seams; like it was never gone
0 2015/07/08 14:53:55
Looks likes this
Looks likes this
0 2015/07/08 14:53:54
Now, issue number two. The bottom of this panel is obviously in need of repair. Cut all the rust off and weld in metal
Now, issue number two. The bottom of this panel is obviously in need of repair. Cut all the rust off and weld in metal
0 2015/07/08 14:53:52
Panel is welded in and cleaned.
Panel is welded in and cleaned.
0 2015/07/08 14:53:51
Not sure if you guys remember what this part looks like before, but it was BAD. Three pieces of metal all rusted and nasty looking
Not sure if you guys remember what this part looks like before, but it was BAD. Three pieces of metal all rusted and nasty looking
0 2015/07/08 14:53:50
As you roll the piece (walk it down) tack... roll, tack, roll tack, Until its in place.
As you roll the piece (walk it down) tack... roll, tack, roll tack, Until its in place.
0 2015/07/08 14:53:49
Once it is secured to the bottom of the panel, use a body hammer and pliers to slowly roll the piece into the desired location
Once it is secured to the bottom of the panel, use a body hammer and pliers to slowly roll the piece into the desired location
0 2015/07/08 14:53:48
Next, tack weld the bottom (flat side) and edges.
Next, tack weld the bottom (flat side) and edges.
0 2015/07/08 14:53:47
I took the contoured old piece, bang it out flat and cut a replacement flat piece
I took the contoured old piece, bang it out flat and cut a replacement flat piece
0 2015/07/08 14:53:45
This is actually a lower door skin for a 1970 Ranchero, lol.
This is actually a lower door skin for a 1970 Ranchero, lol.
0 2015/07/08 14:53:44
0 2015/07/08 14:19:41
0 2015/07/08 14:19:07
Still have to fab the rotten piece I cut out, then put it all back together.
Still have to fab the rotten piece I cut out, then put it all back together.
0 2015/07/02 19:57:56
0 2015/07/02 19:57:48
0 2015/07/02 19:57:39
0 2015/07/02 19:57:21
You make space
You make space
0 2015/07/02 19:57:15
When no space exists...
When no space exists...
0 2015/07/02 19:57:07
All done.. Moving on to the firewall
All done.. Moving on to the firewall
0 2015/07/01 21:14:42
Front channel burned in and welds sealed
Front channel burned in and welds sealed
0 2015/07/01 21:14:36
Replacement channels blasted and Sealed underneath
Replacement channels blasted and Sealed underneath
0 2015/07/01 21:14:27
She cleans up nice
She cleans up nice
0 2015/07/01 21:14:21
Got the old ones off, rust cleaned and sealed
Got the old ones off, rust cleaned and sealed
0 2015/07/01 21:14:16
Scored at the junk yard, rust free Z28. Almost hurt to cut the roof off, but I needed the t-top channels
Scored at the junk yard, rust free Z28. Almost hurt to cut the roof off, but I needed the t-top channels
0 2015/07/01 21:14:09
0 2015/07/01 21:12:30
0 2015/07/01 21:12:16
0 2015/07/01 21:12:10
0 2015/07/01 21:12:04
0 2015/07/01 21:11:58
0 2015/07/01 21:11:53
Yup... That outta do it. Onto the cowl, wish me luck
Yup... That outta do it. Onto the cowl, wish me luck
0 2015/06/23 14:09:37
Looks straight to me
Looks straight to me
0 2015/06/23 14:09:34
Sealed area after
Sealed area after
0 2015/06/23 14:09:29
Clean'er up
Clean'er up
0 2015/06/23 14:09:26
Burn'er in
Burn'er in
0 2015/06/23 14:09:24