Third Generation F-Body Message Boards
0 2018/02/17 16:33:02
Here is the flange I needed off the Air Box to snap the air filter under the remaining air box.
Here is the flange I needed off the Air Box to snap the air filter under the remaining air box.
0 2018/02/17 16:32:24
Cutting off the flange part of the Air Box so that I can still snap the Air Filter on...I had to spend quite a bit of time cleaning up my terrible cut LOL
Cutting off the flange part of the Air Box so that I can still snap the Air Filter on...I had to spend quite a bit of time cleaning up my terrible cut LOL
0 2018/02/17 16:31:18
Look how nice the stock air box looks in there!! Almost factory. But, I'll still need to cut off the bottom of that large air box.
Look how nice the stock air box looks in there!! Almost factory. But, I'll still need to cut off the bottom of that large air box.
0 2018/02/17 16:30:06
Looks good, just needs a coupler now.
Looks good, just needs a coupler now.
0 2018/02/17 16:29:07
Cleaned up my cut, now it just needs a new rubber couple to connect to TB
Cleaned up my cut, now it just needs a new rubber couple to connect to TB
0 2018/02/17 16:28:25
Starting modification...First, cutting off the end at the throttle body to pull it away from the radiator.
Starting modification...First, cutting off the end at the throttle body to pull it away from the radiator.
0 2018/02/17 16:27:14
mocking it up in stock form...in stock configuration the bottom of the air box hits everyting
mocking it up in stock form...in stock configuration the bottom of the air box hits everyting
0 2018/02/17 16:26:21
0 2018/02/17 15:57:54
0 2018/02/17 15:57:44
0 2018/02/17 15:57:34
0 2018/02/17 15:57:22
0 2018/02/17 15:57:09
0 2018/02/17 15:56:53
0 2018/02/17 15:56:35
0 2018/02/17 15:56:26
0 2018/02/17 15:56:09
0 2018/02/17 15:52:07
0 2018/02/17 15:51:38
0 2018/02/17 15:51:11
0 2018/02/11 12:06:08
Ran a couple zip ties to pull in wires even further away from pipes...may change to some stainless wire
Ran a couple zip ties to pull in wires even further away from pipes...may change to some stainless wire
0 2018/02/11 12:05:51
Used some thermo wrap around starter wires
Used some thermo wrap around starter wires
0 2018/02/11 12:05:39
wires all secured...O2 harness
wires all secured...O2 harness
0 2018/02/11 12:05:26
nice shot of clearance
nice shot of clearance
0 2018/02/11 12:05:15
0 2018/02/11 12:05:04
Trying to figure out where to route alternator cable...right now I have it going on radiator support mount
Trying to figure out where to route alternator cable...right now I have it going on radiator support mount
0 2018/02/11 12:04:51
Alternator cable bolted on
Alternator cable bolted on
0 2018/02/11 12:04:27
0 2018/02/11 12:01:44
0 2018/02/11 12:01:19
direct link connector for pcm mounted
direct link connector for pcm mounted
0 2018/02/11 11:58:49
throttle pedal meets 4th gen pedals !!!
throttle pedal meets 4th gen pedals !!!
0 2018/02/11 11:58:12
pedal mounted to mounting plate
pedal mounted to mounting plate
0 2018/02/11 11:57:57
Hawks throttle plate mount for electronic throttle pedal
Hawks throttle plate mount for electronic throttle pedal
0 2018/02/11 11:57:15
0 2018/02/11 11:55:41
0 2018/02/11 11:55:05
0 2018/02/11 11:54:40
0 2018/01/14 16:52:33
0 2018/01/14 16:52:23
0 2018/01/14 16:52:13