Third Generation F-Body Message Boards
0 2022/02/11 11:06:09
0 2022/02/11 10:25:25
0 2022/02/11 10:25:11
0 2022/02/11 08:43:33
0 2022/02/09 12:25:53
0 2022/02/08 19:45:03
0 2022/02/08 19:12:05
0 2022/01/27 10:15:16
0 2022/01/14 11:05:33
0 2022/01/14 11:04:06
0 2022/01/14 09:20:12
0 2022/01/11 08:10:29
0 2022/01/03 17:02:25
0 2022/01/03 17:02:20
0 2022/01/03 17:02:16
0 2022/01/03 17:02:11
0 2022/01/03 17:02:06
0 2022/01/03 16:59:38
Pass. Side with the old brittle cracked weather stripping
Pass. Side with the old brittle cracked weather stripping
0 2022/01/03 16:59:33
I cut a short piece off to see how it’ll fit on the A pillar plastic cover.
I cut a short piece off to see how it’ll fit on the A pillar plastic cover.
0 2022/01/03 16:56:26
0 2021/12/30 23:37:14
0 2021/12/30 23:37:12
0 2021/12/30 23:37:10
Has anyone used these before?
Has anyone used these before?
0 2021/12/30 23:37:08
For some reason Amazon Is saying that this gasket kit doesn’t work but Felpro’s website says it does, certainly wouldn’t be the first time that Amazon doesn’t know what they’re talking about.
For some reason Amazon Is saying that this gasket kit doesn’t work but Felpro’s website says it does, certainly wouldn’t be the first time that Amazon doesn’t know what they’re talking about.
0 2021/12/30 23:37:05
0 2021/12/30 23:36:46
This in the middle top and bottom, towards the top it narrows a little under 1”.
This in the middle top and bottom, towards the top it narrows a little under 1”.
0 2021/12/27 15:20:20
0 2021/12/27 15:15:13
0 2021/12/27 13:14:01
0 2021/12/27 12:39:31
As for the pin locations, I ended up using some pre-existing holes that drilled out larger using a step drill.
As for the pin locations, I ended up using some pre-existing holes that drilled out larger using a step drill.
0 2021/12/25 23:05:17
0 2021/12/25 23:05:12
0 2021/12/25 23:04:41
From here the latches were mounted
From here the latches were mounted
0 2021/12/25 23:00:52
0 2021/12/25 22:59:46
After a lot of deburring and test fitting the latches I masked off the area to pain the inner hood to help protect it from rusting.
After a lot of deburring and test fitting the latches I masked off the area to pain the inner hood to help protect it from rusting.
0 2021/12/25 22:57:53
0 2021/12/25 22:56:39
0 2021/12/25 22:52:20
After the teardrop holes were cut I used a dremal debit and to fine tune the location of the latches, then the mounting holes were located and drilled.
After the teardrop holes were cut I used a dremal debit and to fine tune the location of the latches, then the mounting holes were located and drilled.
0 2021/12/25 22:47:28
0 2021/12/25 22:45:34