Go Back   Third Generation F-Body Message Boards > Tech Boards > DFI and ECM
Register Forgot Password?

DFI and ECM Discuss all aspects of DFI (Digital Fuel Injection), ECMs (Electronic Control Module), scanners, and diagnostic equipment. Fine tune your Third Gen computer system for top performance.

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!

DFI 6 ECU Info

Thread Tools Search this Thread
Old 05-19-2004, 08:30 PM   #1
Supreme Member
Join Date: Sep 2001
Location: Around Mpls, MN
Posts: 1,320
Car: 2009 Pontiac G8 GXP
Engine: LS3
Transmission: 6L80E
Axle/Gears: 3.27

Classifieds Rating: (0)

DFI 6 ECU Info

The ECU/ECM for a TPI was a 74022, in a kit...however, a stand alone or replacement TPI ECU was part # 74046 (which I apparently have)

The calibration file for a stockish TPI 350 is the 74022.all

If the DFI is equipped to use a narrow band O2 sensor, the cal file is 74022A.all

The LT1 cal file (using the 74022 or 74046 ecu) is 74022L.all

The 74023.all is for a 383

The 74024.all is for a 400

I spoke today with Mike at DFI Tech Line, and he was VERY helpful. He stated that the above calibration files were tuned on the dyno initially with these cubic inch engines and should be GREAT base file.

The 74022A (o2 sensor kit) should be pretty spot-on for a stockish TPI 350, but will be a bit rich. Mike reminded me that these are only a base file and still need some tuning for each combo.

Also, he reminded me that a base calibration file can be made using Calmap 6.32, which is what I have and is a free download from the Accel DFI site.

HTH Someone Else....
-88 GTA- 5.7 TPI/700R4, stock
-91 RS/Z28 - 350 TPI, T-5, 3.73 posi, DFI to 730 swap, SLP CAI/Full Exh, etc - down for repairs
88TPI406GTA is offline vBGarage Page   Reply With Quote
Old 05-19-2004, 08:30 PM
1992 Camaro

Paid Advertisement


Go Back   Third Generation F-Body Message Boards > Tech Boards > DFI and ECM

74046, accel, cal, dfi, ecu, files, gen, lt1, manual, mike, o2, read, sensor, tuning, vi
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92

All times are GMT -5. The time now is 03:49 PM.

All content copyright 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details