Glasstek 4" BOLT ON for Camaro
#1
Member
Thread Starter
Join Date: Jan 2011
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
Car: '92 RS
Engine: GM 350 swap
Transmission: T-5
Glasstek 4" BOLT ON for Camaro
This is just my review of the product, take it as you will.
I ordered it from Hawks a while back. It took three weeks to get here, I don't mind because I was on vacation for two of those weeks. It arrived this morning and it took me only two hours by myself to get the old hood off and put this one on.
If you buy this hood, you'll have to get out the dremel and massage some holes . The bolts that come with the hood are bigger than the stock ones. The holes for the hood hinges and for the secondary hood release will need some work.
If you still have the lamp under your hood there are no accomodations on the new hood for it so you'll have to put some brain power into that... The hole for the primary hood latch IS NOT cut out so your hood WILL NOT latch all the way at first. I just took a dremel too it.
As is expected, trimming is required around the edges. I had to go to work so my hood looks kinda funky right now, also I haven't hooked the light back up yet.
All in all it seems to be a good product right off the bat, we'll see later on down the road.
I ordered it from Hawks a while back. It took three weeks to get here, I don't mind because I was on vacation for two of those weeks. It arrived this morning and it took me only two hours by myself to get the old hood off and put this one on.
If you buy this hood, you'll have to get out the dremel and massage some holes . The bolts that come with the hood are bigger than the stock ones. The holes for the hood hinges and for the secondary hood release will need some work.
If you still have the lamp under your hood there are no accomodations on the new hood for it so you'll have to put some brain power into that... The hole for the primary hood latch IS NOT cut out so your hood WILL NOT latch all the way at first. I just took a dremel too it.
As is expected, trimming is required around the edges. I had to go to work so my hood looks kinda funky right now, also I haven't hooked the light back up yet.
All in all it seems to be a good product right off the bat, we'll see later on down the road.
#2
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Glasstek 4" BOLT ON for Camaro
Hey good review. With all fiberglass hoods thier is some fitment issues but don't sound like nothing too bad. way to go
#3
Member
Join Date: Dec 2006
Location: Streator,Illinois
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 camaro
Engine: 409 sbc
Transmission: TH 350
Axle/Gears: 4.10, mini spool, camaro housing
Re: Glasstek 4" BOLT ON for Camaro
Good to hear. Im getting ready to fit my Glasstek hood now. I only live an hour or so from there shop. I was able to drive there and get it. Im going to bolt it to my hinges and use hood pins to latch it. Did you get rid of your cylinders on your hinges that hold the hood up? I wasnt sure if those could still be used.
#4
Junior Member
Join Date: Oct 2006
Location: elbridge new york
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 gta carbed 383
Engine: small block 4bbl
Transmission: 700r4
Axle/Gears: 3.27 g80
Re: Glasstek 4" BOLT ON for Camaro
there are lite duty hood shocks,dont use your normal metal hood ones,it will warp-i found outthe hard way! i had good luck using worn out normal hood struts,but other wise get the fiberglass hood type
#5
Member
Join Date: Jun 2010
Location: Glendale AZ
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 formula
Engine: LG4
Re: Glasstek 4" BOLT ON for Camaro
My worn out ones were to worn to keep my hood up. New stock ones were so strong my hood would start to bend if I didn't have some one help and push it down on both sides.
Im gonna look on summit and see if i can find some that will work.
Thread
Thread Starter
Forum
Replies
Last Post
evilstuie
Tech / General Engine
22
01-09-2020 08:29 PM
84z96L31vortec
Tech / General Engine
7
08-20-2017 12:16 AM
84z96L31vortec
North East Region
1
08-10-2015 08:27 PM