And here she is, done with paint.
#1
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
And here she is, done with paint.
Sorry I haven't gotten around to updating you guys on the new paint job, I haven't really been home since I got the car back, need to get in inspected in less then 3 days till I am screwed. I did get the car back on monday. The only thing that isn't ready is the wing. They should be done with that by the end of this week and will install it for me. Here are a couple pics.
Last edited by XxGeinNothingxX; 03-28-2007 at 02:56 PM.
#4
Member
iTrader: (5)
Join Date: Mar 2004
Location: Orange County, CA
Posts: 336
Received 0 Likes
on
0 Posts
Car: 92 Z28
Engine: LB9
Transmission: 700R4
Axle/Gears: 10 bolt/2.73
Re: And here she is, done with paint.
Very nice
The wing will definately finish it up. Just curious, why did you use the older IROC style grill though?
The wing will definately finish it up. Just curious, why did you use the older IROC style grill though?
#5
COTM Editor
iTrader: (11)
Join Date: Mar 2006
Location: WINDSOR, CO
Posts: 4,098
Likes: 0
Received 12 Likes
on
12 Posts
Car: 91 Z28, 87 SC, 90 IROC, 92 RS
Engine: LS1, 305 TPI, L98, NADA
Transmission: T56, 700r4's, and NADA
Axle/Gears: 3.89, 3.42, 3.23, NADA
Re: And here she is, done with paint.
Looks good! I really like the stripe, and hope it goes to the deck lid too!
#7
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
First of all, great to come in here an hour later and see some awesome coments.
Mike - No the stripe does not go all the way to the rear, I thought about that but decided it would uglify the car. My high rise spoiler is in the paintshop right now, it will go on for you guys.
Plasma - The grill was already on the car when I bought it. I think I like it better than a bowtie though.
Thanks to the rest and their comments.
I also in the past hour finished up the rest of the hood I wanted to be an original job.....including the paint scheme and then this.........
took me about an hour to make templets, had to drill 5 holes on each side
Mike - No the stripe does not go all the way to the rear, I thought about that but decided it would uglify the car. My high rise spoiler is in the paintshop right now, it will go on for you guys.
Plasma - The grill was already on the car when I bought it. I think I like it better than a bowtie though.
Thanks to the rest and their comments.
I also in the past hour finished up the rest of the hood I wanted to be an original job.....including the paint scheme and then this.........
took me about an hour to make templets, had to drill 5 holes on each side
Trending Topics
#9
Member
Join Date: Jan 2006
Location: Garland, texas
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Pontiac Trans Am GTA
Engine: 350 TPI
Transmission: 700r4
Axle/Gears: 3.23 9 bolt
Re: And here she is, done with paint.
that looks for nice. i especially like the black over the cowl. looks sweet
#11
Senior Member
Join Date: Jul 2005
Location: Various barns
Posts: 819
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 Camaro RS, 72 Camaro SS
Engine: 305TBI, til it pukes
Transmission: Auto
Re: And here she is, done with paint.
Yup, Nice job! I'm likin the cowl emblems.
#13
Supreme Member
Join Date: Jul 2003
Location: any clime or place...
Posts: 2,779
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1987 Camaro SC, 1999 Z28
Engine: GMPP 350HO, LS1
Transmission: Built 700r4/EDGE 3200, T56
Axle/Gears: 3.42 Eaton 7.625, 3.42 Zexel Torsen
Re: And here she is, done with paint.
utterly mesmerizing. that has to be the hottest color for 3rd gens of all time.
did u reuse the dark red metallic that came stock in the later years?
gorgeous.
did u reuse the dark red metallic that came stock in the later years?
gorgeous.
#14
Supreme Member
iTrader: (30)
Join Date: Sep 2005
Location: O'Fallon, MO
Posts: 6,258
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Z28 convertible built 3/1/1990
Engine: Cammed 6.0L LSX
Transmission: T56
Axle/Gears: custom Ford 8.8", 4.10 gears
Re: And here she is, done with paint.
Is that Flame Red Metallic?
Whatever it is, it looks great. Good job
Whatever it is, it looks great. Good job
#16
Supreme Member
iTrader: (1)
Join Date: Mar 2001
Location: Chesterfield, Indiana
Posts: 4,226
Likes: 0
Received 6 Likes
on
5 Posts
Car: 1991 Z28 Camaro
Engine: 5.7
Transmission: Jasper 700R4 Stage II
Axle/Gears: 3.23 For Now
Re: And here she is, done with paint.
looks clean man. who did the paint? If the clear side markers are still available...you should get a set. They would look alot better than the orange. Post pictures when you get the highrise installed.
#17
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
For the couple of you that asked about the paint. It was indeed the stock color that came on the car. You can look at my avy and see how much my car was faded before the paint job.
A place around here called B&R autobody painted it.
I do indeed have the clear side markers, I bought them from Kandied.... from off this site, I was looking for some and he offered me his. They will go on after inspection.,
Thanks for the comments.
A place around here called B&R autobody painted it.
I do indeed have the clear side markers, I bought them from Kandied.... from off this site, I was looking for some and he offered me his. They will go on after inspection.,
Thanks for the comments.
#21
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
compuwiz - they look to be some kind of foglights ud find and advanced, the guy who owned the car before me installed them. I actually just took them out, they arent going to pass inspection becuase they are hot all the time, they have to turn off when the high are engaged and i dont feel like putting a relay in.
builtz28- i will have to take the tail light polishing into consideration.
thanks killer clown
builtz28- i will have to take the tail light polishing into consideration.
thanks killer clown
#22
Supreme Member
iTrader: (25)
Join Date: Jul 2004
Location: Beautiful BC
Posts: 2,623
Likes: 0
Received 0 Likes
on
0 Posts
Car: '88 IROC-Z / '91 Z28 / '91 GTA
Engine: LT4 Hot Cam 305 / L98 355 / MR 383
Transmission: 5-spd / 700R4 / 700R4
Axle/Gears: 3:45 / 3:23 / 3:23
Re: And here she is, done with paint.
...looking good...
#23
Senior Member
iTrader: (2)
Join Date: May 2006
Location: Adirondacks, New York
Posts: 711
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 Camaro RS
Engine: 5.0L
Transmission: AUTO, 56k orig
Re: And here she is, done with paint.
awesome! you gave me an idea of what to so with my cowl when i go get er painted, all i can see is some clear parking lights and sidemarkers, sweet ride.
#24
Banned
iTrader: (12)
Join Date: Jul 1999
Location: Bertram (outside Austin), TX
Posts: 12,212
Likes: 0
Received 10 Likes
on
10 Posts
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: And here she is, done with paint.
compuwiz - they look to be some kind of foglights ud find and advanced, the guy who owned the car before me installed them. I actually just took them out, they arent going to pass inspection becuase they are hot all the time, they have to turn off when the high are engaged and i dont feel like putting a relay in.
Instead of taking them off, why not just disconnectc the power, or pull the fuse or bulbs. Claim they are dead, and you just leave them on for looks. Get home, and fix however you "killed" them!
#25
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Must be a state thing? They don't even check fog lights here. I've rewired my to be on, regardless of high/low beams. A simple 5 minute, grounding connection conversion to the stock setup, that could be just as easily reversed, not that I would ever want to.
Instead of taking them off, why not just disconnectc the power, or pull the fuse or bulbs. Claim they are dead, and you just leave them on for looks. Get home, and fix however you "killed" them!
Instead of taking them off, why not just disconnectc the power, or pull the fuse or bulbs. Claim they are dead, and you just leave them on for looks. Get home, and fix however you "killed" them!
#26
Banned
iTrader: (12)
Join Date: Jul 1999
Location: Bertram (outside Austin), TX
Posts: 12,212
Likes: 0
Received 10 Likes
on
10 Posts
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: And here she is, done with paint.
Where are you? You can't remove fog lights? You can't change your hood? What about wheels? Tires?
This sounds a little fishy to me...Are you sure you understand your state laws correctly? This sounds like laws they couldn't have. I suppose you can't change a car's color, or have "racing stripes" either...
This sounds a little fishy to me...Are you sure you understand your state laws correctly? This sounds like laws they couldn't have. I suppose you can't change a car's color, or have "racing stripes" either...
#27
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Where are you? You can't remove fog lights? You can't change your hood? What about wheels? Tires?
This sounds a little fishy to me...Are you sure you understand your state laws correctly? This sounds like laws they couldn't have. I suppose you can't change a car's color, or have "racing stripes" either...
This sounds a little fishy to me...Are you sure you understand your state laws correctly? This sounds like laws they couldn't have. I suppose you can't change a car's color, or have "racing stripes" either...
Commenwelth of VA. The hood won't pass because it is a 3 inch cowl. The legal limit is 2 1/8.
#30
Member
Join Date: May 2006
Location: Fort Wayne, Indiana
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro Iroc-Z
Engine: 350 TPI
Transmission: 700R4
Axle/Gears: 2.77 Posi
Re: And here she is, done with paint.
Car looks sweet man, love the black on the hood!
#31
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
compuwiz, ur lucky, i ALSO have to pass the sniff test as a 305.
I am glad you guys like the hood, I am also glad it turned out awesome. I just wanted somthing that would stand out from any other 3rd gen. out there, same with the emblem....
thanks for the comments.
I am glad you guys like the hood, I am also glad it turned out awesome. I just wanted somthing that would stand out from any other 3rd gen. out there, same with the emblem....
thanks for the comments.
#32
Member
Re: And here she is, done with paint.
That car is sexy! Plain and simple. Nice...
#33
Supreme Member
iTrader: (7)
Join Date: Mar 2005
Location: mid GA
Posts: 1,926
Likes: 0
Received 3 Likes
on
2 Posts
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
Re: And here she is, done with paint.
nice looking car man they did a good job on the paint i really like the cowl induction emblem and that spoiler when it gets on will help the entire look of the car a ton. the stripe is not my style but it doesnt look bad i like to see people trying different stuff anyways and that is a unique idea. post some more pics with the spoiler on!
#35
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Bad-newz - Thanks man
Maroon - I am not sure when I will get pics of the spoiler mounted, my car as of yesterday has dead inspection, so I wont be able to drive it to the paint place to have them mount it. If I call and its done before tuesday, I can just birng it home and mount it myself, but if not, I am leaving wedensday and wont be back for a week, so it might be a while before I get pics, but I will eventually. Thanks for the comments as well.
sprtbike - I am indeed very happy with the outcome, and like everyone is saying, can't wait to see it with the high-rise.
Maroon - I am not sure when I will get pics of the spoiler mounted, my car as of yesterday has dead inspection, so I wont be able to drive it to the paint place to have them mount it. If I call and its done before tuesday, I can just birng it home and mount it myself, but if not, I am leaving wedensday and wont be back for a week, so it might be a while before I get pics, but I will eventually. Thanks for the comments as well.
sprtbike - I am indeed very happy with the outcome, and like everyone is saying, can't wait to see it with the high-rise.
#36
Senior Member
iTrader: (2)
Join Date: May 2005
Location: Manchester, CT
Posts: 591
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 TPI
Transmission: 700R4 Auto
Axle/Gears: 1 legger 2.xx(needs upgrade)
Re: And here she is, done with paint.
sorry to hear about inspection paint looks great! tell em to pass it just because of the paint job!
#37
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Lol, I wish it was that easy. Actually, when I get back I will put the stock hood on, and it will pass. Everything else works, the hood is the only thing stopping me, I already hooked up the stock breather and all to pass the smog check. So, when I get back from AZ, I will drive the bitch to inspection. Then I can also put my clear side markers in.
#38
Member
Join Date: Aug 2006
Location: new york
Posts: 234
Likes: 0
Received 1 Like
on
1 Post
Car: 89camaro rs
Engine: 350tbi (needs carb!)
Transmission: 700r4
Axle/Gears: 32x in process
Re: And here she is, done with paint.
very nice camaro the blk over the cowl gives it like an old skool hot rod look to it ..........i congradulate you on the car
question what size are your rims and tires?
question what size are your rims and tires?
#39
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Here are a couple more pics I jsut took. One of the front with emblem, one of top and right now was the first time I took a pic with the T-tops off. I will post one of that as well.
#40
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Ok, I have came to notice I do not wanna use the HighRise. I really don't wanna mess with drilling holes in the car, I am scared I will mess up and would much rather use stock holes to mount. I am def. going to buy the Hawk's 5 inch and put that on there. I already got my other spoiler painted but have a sudden change in heart. If anyone is looking for a fiberglass high rise, I have it posted in the classifieds. Thanks guys, and also, what do you think about a Hawks 5 inch?
#43
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Thanks for the input guys. I really do think it will look better too, it will all flow together and def. stand out of the crowd even more. The only problem is my hatch is kinda off, so up close it might look a little shitty, but all in all will really stand out.
#44
Supreme Member
Join Date: Jul 2003
Location: any clime or place...
Posts: 2,779
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1987 Camaro SC, 1999 Z28
Engine: GMPP 350HO, LS1
Transmission: Built 700r4/EDGE 3200, T56
Axle/Gears: 3.42 Eaton 7.625, 3.42 Zexel Torsen
Re: And here she is, done with paint.
i like the 5 inch pretty well, but i think it looks even sweeter when they round down the corners a little bit.
#45
Member
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 bored .30 over
Axle/Gears: Posi 342
Re: And here she is, done with paint.
Well, when I took my car for inspection and it passed, I came right home and installed these.
The license plate bracket and the clear side markers.
The license plate bracket and the clear side markers.
#46
Supreme Member
iTrader: (4)
Join Date: Mar 2007
Location: NE Pennsylvania
Posts: 1,690
Likes: 0
Received 3 Likes
on
3 Posts
Car: 85 Iroc-Z
Engine: 383 TPI Procharger D1SC
Transmission: TKO600
Axle/Gears: Strange S60 3.73
Re: And here she is, done with paint.
Great looking car. I like the black and red on the hood.
#47
Banned
iTrader: (12)
Join Date: Jul 1999
Location: Bertram (outside Austin), TX
Posts: 12,212
Likes: 0
Received 10 Likes
on
10 Posts
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: And here she is, done with paint.
Wait a sec...You passed WITHOUT a fugly front plate, then you went home and put one on? Isn't that a little backwards?
Last edited by Stephen; 04-15-2007 at 09:39 AM. Reason: Automerged Doublepost
#48
Senior Member
iTrader: (2)
Join Date: May 2005
Location: Manchester, CT
Posts: 591
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 350 TPI
Transmission: 700R4 Auto
Axle/Gears: 1 legger 2.xx(needs upgrade)
Re: And here she is, done with paint.
Wait a sec...You passed WITHOUT a fugly front plate, then you went home and put one one? Isn't that a little backwards?