Power Window Regulator Rivit Size?
09-07-2008, 07:09 PM
#1
Supreme Member
Thread Starter
Join Date: Mar 2005
Location: Red Lion, PA
Posts: 1,446
Likes: 0
Received 1 Like
on
1 Post
Car: 91 Camaro RS, 99 Camaro Z28
Engine: L03, LS1
Transmission: 700R4, T56
Axle/Gears: bunch of 10 bolts how scary is that
Power Window Regulator Rivit Size?
Anyone know the size rivets needed to replace the rivits for the window regulator?
Also what type of tool do I need to put them in?
I am tired of trying to get my fat hands in there to put bolts in.
Also what type of tool do I need to put them in?
I am tired of trying to get my fat hands in there to put bolts in.
09-07-2008, 09:11 PM
#2
Member
Join Date: Apr 2000
Location: Orlando, FL USA
Posts: 312
Likes: 0
Received 1 Like
on
1 Post
Car: 89 Formula 350
Engine: 5.7 TPI
Transmission: 700R4
Re: Power Window Regulator Rivit Size?
1/4" peel rivets and use this:
http://www.harborfreight.com/cpi/cta...emnumber=41291
I am painting a door right now and I am thinking about tack welding small nuts on the regulator. That way I can just screw or bolt it in.
http://www.harborfreight.com/cpi/cta...emnumber=41291
I am painting a door right now and I am thinking about tack welding small nuts on the regulator. That way I can just screw or bolt it in.
09-10-2008, 02:17 AM
#3
Member
Join Date: Jul 2005
Location: Staten Island NY
Posts: 372
Likes: 0
Received 0 Likes
on
0 Posts
Re: Power Window Regulator Rivit Size?
When I replaced my driver side PW motor, I used the little screw & nut that came with the new motor on 2 of the holes. On the third hole, where it seemed impossible to hold the nut in place, I used a sheet metal screw and it has held fine (over 2 years).
09-14-2008, 11:39 AM
#4
Member
Join Date: Oct 1999
Location: Alamogordo, NM, USA
Posts: 261
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1969 Z/28, 1983 Z/28
Engine: 350, 305 (L69)
Transmission: TKO-600, T5
Axle/Gears: 3.42, 3.73
Re: Power Window Regulator Rivit Size?
1/4" peel rivets and use this:
http://www.harborfreight.com/cpi/cta...emnumber=41291
I am painting a door right now and I am thinking about tack welding small nuts on the regulator. That way I can just screw or bolt it in.
http://www.harborfreight.com/cpi/cta...emnumber=41291
I am painting a door right now and I am thinking about tack welding small nuts on the regulator. That way I can just screw or bolt it in.
Larry
09-14-2008, 01:32 PM
#6
Junior Member
Join Date: Aug 2008
Location: NJ
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS Conv
Engine: 305 V8
Transmission: Auto
Re: Power Window Regulator Rivit Size?
i did mine not 2 weeks ago....i just used a standard 3/16 rivet and i put a washer on both sides of the rivet (with the help of a friend) and they held up pretty good.
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
