Hatch out of ajustment?
#51
Junior Member
Join Date: Jul 2012
Location: The Blast Furnace, AZ
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Trans Am
Engine: 305 4bbl
Transmission: 700R4
Axle/Gears: 2.73:1 open
Re: Hatch out of ajustment?
Mine was a good half-inch or more out, I just adjusted at the hinge by loosening the fasteners, pushing it forward, and retightening. It's more like a quarter-inch now, good enough for the moment.
#52
Supreme Member
iTrader: (4)
Re: Hatch out of ajustment?
I just adjusted mine at the hinge. The best way to do it is to remove the struts and then you can move the hatch where it needs to be. I was initially trying to do it with the struts connected and could not get it right. I took off the struts and got it where it needed to be the first time out.
#53
Member
Join Date: Nov 2009
Location: Sarasota, FL
Posts: 338
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 GTA
Engine: 400 CI
Transmission: 700R4
Re: Hatch out of ajustment?
I had already moved mine forward at the hinge and even checked the body bolts. It was off almost and inch after that. The only way to get it close was to reset the panel.
#54
Member
iTrader: (1)
Join Date: Jun 2010
Location: Buffalo, NY
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 10 Bolt 3.42 Posi
Re: Hatch out of ajustment?
you didnt have to take the whole hatch off did you? I have been to lazy to do mine because I know that glass weighs a TON if i have only one side out of wack could I just remove that side and slide that side of the hatch up and readjust?
#56
Member
Join Date: Nov 2009
Location: Sarasota, FL
Posts: 338
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 GTA
Engine: 400 CI
Transmission: 700R4
Re: Hatch out of ajustment?
Correct. You don't have to take the hatch off to adjust it at the hinges. But you will have to disconnect the struts from the hatch or when you loosen the hinge the hatch will be pushed back but them.
#57
Member
Join Date: Nov 2009
Location: Sarasota, FL
Posts: 338
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 GTA
Engine: 400 CI
Transmission: 700R4
#58
Member
Join Date: Dec 2001
Location: Burnaby, BC, Canada
Posts: 471
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro Iroc-Z
Engine: 305 TPI (LB9)
Transmission: Auto 4
Re: Hatch out of ajustment?
We just have to remember we're working with a pinch welded mass produced car built mostly in the 80s. Things not lining up perfect is normal.
#59
Junior Member
Join Date: Jul 2012
Location: The Blast Furnace, AZ
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Trans Am
Engine: 305 4bbl
Transmission: 700R4
Axle/Gears: 2.73:1 open
Re: Hatch out of ajustment?
I have a much harder time when the discrepancies are so great that possibly the hatch won't latch down when closed...
#61
Junior Member
iTrader: (1)
Join Date: Sep 2002
Location: Williamsburg, VA
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z28
Engine: 350 L98
Transmission: 700R4
Axle/Gears: G92 - 3.23
Re: Hatch out of ajustment?
My 91 Z28 looks the same as yours. I think I need a combo of glass to hinge adjustment and the bottom panel adjustment.
Thread
Thread Starter
Forum
Replies
Last Post
formula00ra
Interior Parts Wanted
1
09-28-2015 11:50 AM
1Aauto
Sponsored Vendors
0
09-23-2015 01:09 PM
1Aauto
Sponsored Vendors
0
09-23-2015 01:00 PM