edelbrock???
#1
Member
Thread Starter
Join Date: Dec 2001
Location: ohio
Posts: 194
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1982 camaro
Engine: built 355 chevy
Transmission: th 350 w/ 3.73 gears
edelbrock???
Ok, heres the deal, i have a 1982 Camaro, 3.73 posi rear, th350 trans with shift kit and 3500 stall, 355 SBC with world sr torquer 2.02 heads, 10-1 comp, .530 lift cam 30/30 cam, 1.6-1 roller tip rockers, mallory ignition, flowmaster exhaust with holley shorty headers, currently a 750 cfm Edelbrock,
I took it to the trak last week and ran a 14.6 with a 1.90 60', it wouldnt pull at top end, so i put a single plane intake on it to help and because i suspected a vac leak. now i can turn my air/fuel screws anyway i want with no change, idle doesnt go up or down, wouldnt this suggest i have a vac leak?? shouldnt the engine die when i closed these screws?? this car is makeing me pull my hair out and just doesnt have the power it should
Russell
I took it to the trak last week and ran a 14.6 with a 1.90 60', it wouldnt pull at top end, so i put a single plane intake on it to help and because i suspected a vac leak. now i can turn my air/fuel screws anyway i want with no change, idle doesnt go up or down, wouldnt this suggest i have a vac leak?? shouldnt the engine die when i closed these screws?? this car is makeing me pull my hair out and just doesnt have the power it should
Russell
#2
Supreme Member
Join Date: Aug 2005
Location: Yellowknife, NWT, Canada
Posts: 3,004
Likes: 0
Received 2 Likes
on
2 Posts
Car: 84 Z28
Engine: 357
Transmission: TH-350C
Axle/Gears: 3.43
Yes it should start to miss when the screws are too far in or out (lean/rich). I have had a hella time setting mine up nicely and after a whole summer i still think it can do better.
My next buildup is getting a holley or something...
My next buildup is getting a holley or something...
#6
Supreme Member
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
which edelbrock carb ?
did you check to see if the metering rods are sitting in the seats right? Floats adjusted right etc....
did you check to see if the metering rods are sitting in the seats right? Floats adjusted right etc....
#7
Member
Join Date: Apr 2005
Location: North Texas
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
Engine: sbc 350
camaro03,
can you get your hands on a vacuum guage?
if so, you might try this test,
hook it up to look a nanifold vacuum when driving.
at WOT, vacuum should be, guessing, 3 psi or less..
if you have lots of vacuum at WOT, there is
some kind of a restriction.
can you get your hands on a vacuum guage?
if so, you might try this test,
hook it up to look a nanifold vacuum when driving.
at WOT, vacuum should be, guessing, 3 psi or less..
if you have lots of vacuum at WOT, there is
some kind of a restriction.
Thread
Thread Starter
Forum
Replies
Last Post
Pac J
Tech / General Engine
3
05-17-2020 10:44 AM
efiguy
Engine/Drivetrain/Suspension Parts for Sale
0
09-27-2015 01:30 PM
Night rider327
Engine/Drivetrain/Suspension Parts for Sale
0
09-25-2015 04:47 AM