Question about fusible links
#1
Question about fusible links
Ok so I've been looking around the internet for a fusible link that looks like the round cylinder with the stamp or 20 and 16 but I can't find anything ! So are most fusible links you get at an auto parts store exceptible or am I just missing where to purchase these ?
#2
Moderator
iTrader: (1)
Join Date: Mar 2002
Location: Chasing Electrons
Posts: 18,409
Likes: 0
Received 217 Likes
on
203 Posts
Car: check
Engine: check
Transmission: check
Re: Question about fusible links
They are the factory links, only way to get those is to buy a whole factory harness. The cylinder is molded and covers the splice between the link & main wire. And the number stamped in it is the fusible link size (gage).
Get the auto store links with the proper ring lug. Cut the splice off the main wire, and splice/crimp the link onto it. Cover splice with some RTV and heat shrink.
RBob.
Get the auto store links with the proper ring lug. Cut the splice off the main wire, and splice/crimp the link onto it. Cover splice with some RTV and heat shrink.
RBob.
The following users liked this post:
vorteciroc (05-09-2023)
#3
Supreme Member
Join Date: Jul 2006
Location: 212 is up in this Bit@#
Posts: 2,768
Received 741 Likes
on
567 Posts
Car: Resto-Mod 1987 IROC-Z Clone
Engine: Alky fed L92 Vortec Twin-Turbo 6.8L
Transmission: My own built/ design 4L80M
Axle/Gears: Custom 12 bolt (4.10:1)
Re: Question about fusible links
Just as the Two Gentlemen above me "PERFECTLY" Posted...
The Component that appears as a Black Plastic Cylinder, is not part of the actual "Fusible-Link".
It is essentially a Butt-Splice Terminal that has a protected Heat-Molded Plastic Cover over it.
It also has an Identification Number in the Plastic Mold.
This is to Identify which/ what Gauge Wire the Fusible-Link is.
Generally, this is what you will find on our Old OEM Packard-Electrical-Division Fusible-Links:
-A 14AWG Wire with a 18AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 12AWG Wire with a 16AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 10AWG Wire with a 14AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 8AWG Wire with a 12AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
The Component that appears as a Black Plastic Cylinder, is not part of the actual "Fusible-Link".
It is essentially a Butt-Splice Terminal that has a protected Heat-Molded Plastic Cover over it.
It also has an Identification Number in the Plastic Mold.
This is to Identify which/ what Gauge Wire the Fusible-Link is.
Generally, this is what you will find on our Old OEM Packard-Electrical-Division Fusible-Links:
-A 14AWG Wire with a 18AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 12AWG Wire with a 16AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 10AWG Wire with a 14AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
-A 8AWG Wire with a 12AWG Fusible-Link and ID Number on the Black Plastic Cylinder.
The following users liked this post:
T.L. (05-09-2023)
#4
Re: Question about fusible links
Sorry for the late reply! thanks guys ! I've been posting alot so I'm just trying to make sure I get ideas from everybody about alot of things. Maybe you guys can help me ? I'm dropping the tank on the car should I replace the whole fuel sender unit? Or just stick to replacing the fuel pump ?
#5
Supreme Member
iTrader: (1)
Join Date: Dec 2000
Location: Cincinnati,Ohio
Posts: 2,341
Received 151 Likes
on
111 Posts
Car: 1991 BandittII Firebird
Engine: 5.7 HSR
Transmission: 700R4
Axle/Gears: 3.27 9 bolt
Re: Question about fusible links
Sorry for the late reply! thanks guys ! I've been posting alot so I'm just trying to make sure I get ideas from everybody about alot of things. Maybe you guys can help me ? I'm dropping the tank on the car should I replace the whole fuel sender unit? Or just stick to replacing the fuel pump ?
EDIT: Found this post by vorteciroc, good advise
"I personally will connect the new Sending-Unit before installing it into the Fuel Tank.
Then I will turn ON the Ignition Switch, and move the Float-Arm of the SendingUnit by hand.
Having someone else watch the Fuel Gauge, make certain that the SendingUnit operates properly.
Note most Sending Units from this era will be Grounded via contact with the Fuel Tank.
In this situation, a wire is needed to contact the Body of the SendingUnit to a Ground Location on the Car.
You will have to see if the Variable Resistance of the SendingUnit, matches the specified range.
Take these measurements on the SendingUnit, and then at the Fuel Level Gauge Connection.
This can help rule-out a Wiring issue/ excessive resistance."
The following users liked this post:
T.L. (05-23-2023)
The following users liked this post:
91banditt2 (05-23-2023)
Thread
Thread Starter
Forum
Replies
Last Post