red406

iTrader: (4)

Here is my rear axle for sale. It is a Moser housing and 31 spline axles, with a Currie 9+ third member. It has 4.11:1 ratio and a posi. Third member is rated to 650 hp. I bought the housing and axles new from Moser on 3/16/05. I used it for three seasons putting about 1K miles on it. I have never had slicks bolted up. The lower control arms are Lakewood and are included. Brakes are Torino drum brakes. Bolt pattern is for Camaro or Firebird and is metric studs (12mm). I have almost 2800.00 in this package.

Also included. Stock panhard rod and brace, and shocks (not pictured)

I decided to prostreet my Camaro and I need this gone.

I'm located in New Waterford, Ohio

I'm asking 2000.00. Sorry, no shipping.

red406

iTrader: (4)

Forgot to mention that this is stock width for a third gen.

We'reNotWorthy

I'm very very interested pm and we can talk. How far are you from the Akron area.

red406

iTrader: (4)

PM sent!

red406

iTrader: (4)

Bump!

85ZzZ4

will i be able to run a stock length driveshaft if i purchase this rear end?

red406

iTrader: (4)

Thats a good question. When I first installed this axle, I changed the whole drivetrain in my car. I installed a TH400 and I had to get a new driveshaft made anyway.

At the very least you may need a conversion u-joint (chevy to ford).

kowboy59

iTrader: (8)

if you werent in ohio id prolly get money to take this from you. lol orlando is kind of far

red406

iTrader: (4)

You should make a trip to Ohio to see the wonderful weather. It is a warm and sunny 30 degree day today. I wish I lived in Florida.

85ZzZ4

i'm trying to work out some finances for this rear end... interested in any trades? N.O.S wet kit, 20" dip racing wheels with tires? tax check doesn't quite cover the whole amount... anything else you can think of, i have a ton of third gen parts, let me know if you need anything and i'll see if i have it...

red406

iTrader: (4)

I'm looking for a non ac dash, black carpeted console, and black door panels.

jstoltz

iTrader: (16)

if you were interested in meeting halfway I was somewhat interested in the sumped gas tank and sender you have and I have an extra non a/c dash. I would just make the drive but if mapquest is correct it is a little over 3 hr drive.

red406

iTrader: (4)

I really need this axle out of my way. I will throw in two torque arms! At no extra cost! One torque arm is a factory unit and the other is an Edelbrock (p/n 5280 paid $175.88 on 04/17/05). I had to modify the Edelbrock arm to fit the bracket on the 9 inch housing. I got it to fit but the torque arm rubbed the d/s tunnel. I ended up putting a stock torque arm back in and it fit perfect.

bearws6

I wanted to know if you would sale the controle arms and ship.
i have the same 9" in my 3g car and was able to run the stock driveshaft..

red406

iTrader: (4)

Bump!

JohnyP

iTrader: (3)

hey did you ever see if you wanted to ship i saw you bumped the thread. i really would like to buy. If you absolutely cant ship it ill make the drive but its 7 1/2 hrs to get there so either a meet somewhere by you or a ship would be wayyyy beter. let me know have cash ready.will pay extra and shipping if you ship

red406

iTrader: (4)

PM sent.

1fastrock

Do you still have it and would be intrested if we can work something out

red406

iTrader: (4)

I still have it, but I have someone interested.

1fastrock

allright let me know if you still have it

red406

iTrader: (4)

Sold!