WIll36

iTrader: (12)

here is the list

link with pictures
rotating assembly http://s244.photobucket.com/albums/g...ng%20assembly/
most other stuff http://s244.photobucket.com/albums/g...f%20to%20sell/
distributor http://s244.photobucket.com/albums/g...20distributor/

the973camaroguy

any pics of the fiber glass nose my email adress is bocajr88@aol.com

WIll36

iTrader: (12)

yes forgot that link http://s244.photobucket.com/albums/g...lass%20pieces/

cliff1970

any seat pics? nevermind, found them

FUNIROC

iTrader: (4)

Do you have any red front seatbelt receivers?

Thanks

WIll36

iTrader: (12)

[QUOTE=FUNIROC;4410795]Do you have any red front seatbelt receivers?

The car had a red interior. I'm not sure if I held onto those or if they are any good. I'll look around in the next couple days and let you know if I find them.

FUNIROC

iTrader: (4)

That would be great.

Thanks

TommyG

Interested in 406 kit. Miles, Bore Size of piston, Rod length, Comp ratio, 2 pc seal or 1 any and all info would be helpful. Thank you much!

WIll36

iTrader: (12)

It's been apart for about 2 years now, but I stored all the parts inside with oil on them. However my memory on the milage isn't the best I want to say about 8 or 9 thousand miles since the crank was turned and the new pistons installed. Anyway the crank journals have been cut 10 thousands and the rods were cleaned and magged. Both crank and rods are stock so it's a 3.75 inch stroke with 5.625 inch rods on a stock 400. The pistons are 30 over making it 406 cubes instead of 400. Also all 400s are 2pc RMS. Your final compression ratio will depend on what block it goes in (deck height), head gasket thickness and how many cc's your heads combustion chambers are. Those are flat top pistons so I would guess 9 to 1 ish with 72cc heads but that is just a guess and there are really too many variables to say accurately without more information. Those pistons did work fine on the street with smaller chamber heads but it was always run on premium ethanol free fuel. Hope that answers your questions.

WIll36

iTrader: (12)

bump

WIll36

iTrader: (12)

bump

WIll36

iTrader: (12)

bump

cleanwater7

Door moldings? Outside sealiing molding?

WIll36

iTrader: (12)

are you looking for the soft seals for the doors and the lower plastic piece or all of it???

cleanwater7

rubber soft seals

WIll36

iTrader: (12)

I dont remember what kind of shape they are in. I'll check tomorrow when I get more pics of the car and parts.

JTNKTZ

iTrader: (10)

wieand accelerator intake (somebody started modding to fit early heads) - make offer

I'm confused, will this fit my post 87 block?
What do you mean modding to fit early heads?
Would it effect over all performance and/or function?
Pictures?
Did I ask enough questions?
Thanks! PM if you could as well.

WIll36

iTrader: (12)

Sorry got that backwards. The intake is for the older style heads where the center 4 bolts for the manifold face straight down. So to use this on an 86 up set of heads you would have to finish modifying the manifold with a dremel or equivalent. It's fairly common to do, as long as the manifold seals it doesn't affect performance at all. Also have a holley carb and MSD distributor to sell.

picture http://s244.photobucket.com/albums/g...t=HPIM1363.jpg

G-4ce

iTrader: (1)

how much for carb and dizzy? and shipped to 34952?

cleanwater7

Can you send pics on the door seals? Not sure what you mean by the plastic parts.

WIll36

iTrader: (12)

The hard plastic interior pieces I'm not interested in selling at this point. Maybe in another month or 2 when my 91 Z28 project is done. Don't want to sell something and wind up needing it.

cleanwater7

OK so $20 for the rubber seals.

Send me details on how to get $ money to you if interested.

WIll36

iTrader: (12)

I'll take some pictures today so you can see what they look like before you say that you definetly want them.


Sold the brakes and spoiler locally

WIll36

iTrader: (12)

http://s244.photobucket.com/albums/g...ed%2091%20Z28/

photos that cleanwater7 asked for

WIll36

iTrader: (12)

bump updated list and removed parts that have sold

mjk1210

Does the carb have vacuum or mechanical secondaries?

tomwilson

iTrader: (1)

do the fog lights have brackets and what cond are they?

WIll36

iTrader: (12)

the carb is vaccum secondaries

foglights are sold pending me recieving payment I'll let you know if the deal falls through.

pr0zac

any progress on it??

WIll36

iTrader: (12)

been busy last 2 months plowing and all. Getting back in gear working on it, just need my brakes from Ed. I'm actually heading over to the shop to work on installing that cage now. http://s244.photobucket.com/albums/g...m/91%20camaro/

Blew-By-You

Hi, 3 questions: Would you consider seperating the steering wheel from the column? How about the carpeted center console? and finally, that looks like a 145mph speedo, any chance of that being sold? Thank you!

WIll36

iTrader: (12)

Yes I will sell the wheel without the column. They weren't really f/s together just took the pictures that way. I don't have the console anymore and I will sell the cluster. Not sure on prices PM me an offer and zip code.

skidoodave

Will you seperate the blisters from the hood? if so, how much?

mchenryb1988

iTrader: (1)

Rear leather seats? 50.00? +shipping to 31405

Samdweezel05

iTrader: (1)

Where in NY, I am interested in the 406.

WIll36

iTrader: (12)

mchenryb1988- I can do that price on the rears. I'll look into shipping today or tomorrow and PM you

Samdweezel05- I'm in Plattsburgh area. Might be able to meet half way if your interested in the whole motor.

PMs replied to

Samdweezel05

iTrader: (1)

LMAO, I'm in Chazy. Might be a bit of a haul. Half way would be Stuckies of exit 40, lol.

WIll36

iTrader: (12)

Well that makes everything a lot easier. PM me a phone number and I'll get ahold of you tomorrow.