rffy

iTrader: (1)

I have to sell my engine / tranny combo. This engine has about 500 miles on it and ran fine before it was pulled.
I have receipts totaling at least $5000. I am asking $2200 for engine/trans.
If I have to separate I will sell the trans with torque converter for $600 FIRM and the motor for $1650 FIRM. Cash only. Local pickup only. I am located near Akron, Ohio. I won't split up the trans/torque converter.
Some Details:
Summit .030 over 383 block fully machined. Summit 200cc aluminum heads. 64cc 2.02/1.60 etc. (~10.5 to 1cr). Cast crank, roller rockers, forged I beam rods with cap screws. Balanced assembly. 7qt pan. Lunati hyd camshaft 60103Lk part #. (this block accepts roller cam as well)
link to rotating assembly : http://www.summitracing.com/parts/esp-b13405l03053
transmission is Summit part # TCI-311003 (super streetfighter Turbo 350 short tail shaft)
Block is summit part # SUM-150100
Heads are summit part # SUM-162112
I have the car this came out of so if needed we could work something out on matching y pipe/headers which bolted up to this engine.
PM me for details. I am not interested in trades at this time. Serious inquiries pls. You can also email me at rfitz2@hotmail.com . Put engine in the subject line so I don't miss it. I am not on this site a ton but I will check the post.

cattiveria665

iTrader: (1)

what's the hp and tq specs roughly on the engine?

rffy

iTrader: (1)

I never had this on the dyno but a conservative estimate would be 400-420HP and 450FT lbs torque. It requires 91 octane.

cattiveria665

iTrader: (1)

Ok man sounds nice I'll def give it some thought

CashMunson

iTrader: (1)

still for sale?

rffy

iTrader: (1)

yeah it is. I have been working a lot so I haven't had time to try to sell it very hard.

CashMunson

iTrader: (1)

What all comes with the engine, if bought seperate?

rffy

iTrader: (1)

Everything you would reasonably expect to come with an engine.

600cfm edelbrock carb
Long block as seen in pics (carb to pan)
High torque mini-starter
You would need a power steering pump.
like new 1 wire alternator with summit alt bracket
any pulleys I have in the garage that came off it. I think I have one that bolts to the harmonic balancer.
Plugs and wires go with it. NGK plugs and new mallory wires


Let me know if you have any more questions.

CashMunson

iTrader: (1)

would you be interested in a prepped 350 block and some cash for the engine?

nogal

Hi - I sent you an email few days ago, have you received it ?

rffy

iTrader: (1)

Yes I did. Sorry it was in my filtered email. I cannot ship overseas. I am sorrybut it's too much trouble for an individual to send something that large overseas. I can only offer this item for local pickup.

rffy

iTrader: (1)

That depends completely on your offer. PM me with what you were thinking. Keep in mind you can buy a late model roller 383 prepped block from summit for $500.

rffy

iTrader: (1)

list of some components. I am asking less than I paid for just the shortblock.

TP355Z

Looks like a nice combo - why are you selling it?

rffy

iTrader: (1)

I have a 2010 mustang gt and I lost interest in this project. I took the motor and trans out to install the kickdown cable in the tranny and replace the trans mount but I never got enough interest in it to put it back in the car.

badazta87

iTrader: (1)

PM sent

gcj280

iTrader: (15)

Is this still for sale?

thanks, Greg

rffy

iTrader: (1)

Shortblock is sold. Thanks badazta87!

I still have the aluminum heads, roller rockers, transmission, and intake.

These will be offered for sale shortly.

rffy

iTrader: (1)

Heads are $500 firm. They will fit all SBC including 400. There are instructions in the box that detail 400 installation.

http://www.summitracing.com/parts/sum-162112

Transmission plus 10' torque converter is $550. This tranny is good to 550 HP.

http://www.summitracing.com/parts/tc...make/Chevrolet

I prefer pickup but would look into shipping the heads. They are heavy but I do have the original box.

gcj280

iTrader: (15)

how much for the heads shipped to 71047?

thanks, Greg

gcj280

iTrader: (15)

are the headers and y-pipe available for sale? do they go in a camaro?

Aardwolf

PM sent.

rffy

iTrader: (1)

You guys can calculate shipping at the post office website, usps.com .

I would estimate around 50lbs.

24' length x 14' width x 10' height on the package.

It looks like around $50 to most places 3 or 4 day shipping time.

rffy

iTrader: (1)

Sorry, headers and y-pipe stayed with the car.

Aardwolf

$50 shipping for the heads would be fine. I will buy them. Will Paypal be okay?

rffy

iTrader: (1)

PM sent

rffy

iTrader: (1)

heads are sold!!

Aardwolf

Heads got here. Look good!

rffy

iTrader: (1)

good deal. Glad to hear. good luck with them!