INTAKE MANIFOLD - Sold
#3
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
Below are photos of Moroso part numbers 63425 and 63426 remote thermostat housings. I recommend using one of these. Run the two included hoses, from the rear coolant fittings, into the remote thermostat housing. Then connect your water neck and upper radiator hose to the remote housing. The rear manifold connection hoses can either be run to the drivers side, or run up underneath the plenum & runners, & out under the throttle body.
Last edited by formulaman; 01-20-2014 at 06:19 PM.
#4
#5
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
No, I have installed it on an engine, but never ran the engine. I did pressure test the coolant system on the engine though, so I know that the manifold seals well with the provided gaskets.
Last edited by formulaman; 01-20-2014 at 06:17 PM.
Trending Topics
#8
Member
iTrader: (3)
Join Date: Jul 2010
Location: Athens, Tn
Posts: 164
Likes: 0
Received 2 Likes
on
2 Posts
Car: 87 GTA
Engine: 350
Transmission: 700r4
Axle/Gears: 3.42 posi
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
I'm curious as to why spend spend all the money and time on this intake and never really run it? What's the reason for selling?
#10
Supreme Member
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
whats up with the distributer hold down tapped block? is that epoxyed on?
#12
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
Well, I really would like to get this sold. Due to the lack of action here, I'll have to put it on that big auction site tonight. Everyone here is more than welcome to bid on it. I'll list it as "custom efi tunnel ram" and I'll start it real low, and you can put in whatever it is worth to you.
#13
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
Well, I really would like to get this sold. Due to the lack of action here, I'll have to put it on that big auction site tonight. Everyone here is more than welcome to bid on it. I'll list it as "custom efi tunnel ram" and I'll start it real low, and you can put in whatever it is worth to you.
#14
Supreme Member
iTrader: (1)
Join Date: Apr 2008
Location: Utah
Posts: 10,401
Likes: 0
Received 2 Likes
on
2 Posts
Car: 89 RS 89 iroc 87 firebird
Engine: 3.1 Turbo/ 355 twin turbo
Transmission: a4 w/ 4500 stall/ a4 / t5
Axle/Gears: strange s60 /w 3:42's
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
im willing to throw a few bids at it , just curious as to if it would match up well with a dart pro 1 platnium intake port , this is a rasied runner head , which requires a raised runner or vortec intake
#17
Supreme Member
iTrader: (1)
Join Date: Apr 2008
Location: Utah
Posts: 10,401
Likes: 0
Received 2 Likes
on
2 Posts
Car: 89 RS 89 iroc 87 firebird
Engine: 3.1 Turbo/ 355 twin turbo
Transmission: a4 w/ 4500 stall/ a4 / t5
Axle/Gears: strange s60 /w 3:42's
Re: Custom SBC EFI Tunnel Ram INTAKE MANIFOLD!
i didnt catch this till 2 hours before the end of auction ( so its my fault for not getting a reply from him intime ) but i was going to throw a bid on it , didnt wanna take the chance of not knowing if the ports would line up with my new heads though
i didnt win it , not sure if who did is from tgo or not
i didnt win it , not sure if who did is from tgo or not
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM