Performance Parts
03-17-2015, 03:37 PM
#1
Supreme Member
Thread Starter
iTrader: (35)
Join Date: Feb 2003
Location: Albuquerque, NM
Posts: 1,229
Likes: 0
Received 3 Likes
on
2 Posts
Car: 1966 El Camino Custom
Engine: 350
Transmission: 200R4
Axle/Gears: 3:73 12 bolt with Brute Strength
Performance Parts
Any interest in these performance SBC parts? I've got a split combination (1.52/1.6) set of Comp Cams Pro Magnum rocker arms. They are a full roller rocker. Non-self aligning. Guide plates included. $175 + shipping.
A set of CP forged pistons. Originally manufactured for SB2 but they will work for a budget 400 SBC build with 6" rods. They are dished. They are 4.125" + .010 over size. They have dyno time only. One piston had to be replaced. It cracked under a NOS hit. Skirts are very nice. I did send them back to CP and they are verified to be in very good condition. $250 + shipping.
A set of CP forged pistons. Originally manufactured for SB2 but they will work for a budget 400 SBC build with 6" rods. They are dished. They are 4.125" + .010 over size. They have dyno time only. One piston had to be replaced. It cracked under a NOS hit. Skirts are very nice. I did send them back to CP and they are verified to be in very good condition. $250 + shipping.
03-18-2015, 07:34 AM
#4
Junior Member
iTrader: (2)
Join Date: Jul 2013
Location: pennsylvania
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 iroc z, 03 ram 1500
Engine: 305 tpi, 287
Transmission: WC T5, NV3500
Axle/Gears: 3.42, 3.55s
Re: Performance Parts
Do you know about how many miles are on them?
03-18-2015, 10:52 AM
#5
Supreme Member
Thread Starter
iTrader: (35)
Join Date: Feb 2003
Location: Albuquerque, NM
Posts: 1,229
Likes: 0
Received 3 Likes
on
2 Posts
Car: 1966 El Camino Custom
Engine: 350
Transmission: 200R4
Axle/Gears: 3:73 12 bolt with Brute Strength
Re: Performance Parts
Less than 15,000. They are in very good condition. No issues. They are rebuildable but are no where close to that. You'll be happy with them. They must be used with rocker arm studs because that's how the guide plates mount.
03-18-2015, 12:32 PM
#6
Junior Member
iTrader: (2)
Join Date: Jul 2013
Location: pennsylvania
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 iroc z, 03 ram 1500
Engine: 305 tpi, 287
Transmission: WC T5, NV3500
Axle/Gears: 3.42, 3.55s
Re: Performance Parts
Ok so they should bolt right on to my 85 305?
03-18-2015, 03:13 PM
#7
Supreme Member
Thread Starter
iTrader: (35)
Join Date: Feb 2003
Location: Albuquerque, NM
Posts: 1,229
Likes: 0
Received 3 Likes
on
2 Posts
Car: 1966 El Camino Custom
Engine: 350
Transmission: 200R4
Axle/Gears: 3:73 12 bolt with Brute Strength
Re: Performance Parts
Do your heads have screw-in studs? You need screw-in studs so you can mount the pushrod guide plates. See photo. If your heads have pressed in studs, they will not work.
Trending Topics
03-18-2015, 03:49 PM
#8
Junior Member
iTrader: (2)
Join Date: Jul 2013
Location: pennsylvania
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 iroc z, 03 ram 1500
Engine: 305 tpi, 287
Transmission: WC T5, NV3500
Axle/Gears: 3.42, 3.55s
Re: Performance Parts
Crap I still have the stock pressed in ones. Thanks
Thread
Thread Starter
Forum
Replies
Last Post
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
20
11-14-2015 12:02 AM
86IROC112
Engine/Drivetrain/Suspension Parts for Sale
4
08-17-2015 02:00 PM