Loudes exhaust for a 84 z28
03-30-2012, 12:12 AM
#1
Senior Member
Thread Starter
iTrader: (3)
Join Date: Jan 2011
Location: Oxnard, CALI
Posts: 842
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1984 Z28
Engine: 5.0 L (Carbed)
Transmission: 5-Speed
Axle/Gears: Lazy 2 check
Loudes exhaust for a 84 z28
So I got a stock 1984 z28 carburated camaro. and I was wondering what would be the best performance wise and loudest exhaust system out there. I used to have a flowmaster 80 series on a 87 and that wasn't half bad, but I am also not looking to spend $1000 on a system. So would wan something reasonably prices but also loud, thanks!
03-30-2012, 04:38 AM
#4
Junior Member
Join Date: Dec 2009
Location: St.John's, Newfoundland, Canada
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Camaro Z28
Engine: 355 4 bolt 4bbl
Transmission: T-5 manual
Axle/Gears: 3.73 posi.
Re: Loudes exhaust for a 84 z28
first, you need headers....3" Intermediate pipe....and maybe an SLP loudmouth muffler.
This is what I had on my car, but was too loud for me. (My local laws)
This is what I had on my car, but was too loud for me. (My local laws)
03-30-2012, 01:11 PM
#5
Member
Join Date: Aug 2011
Location: Eureka, IL
Posts: 128
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Trans Am GTA
Engine: Vortec Stealth Rammed L98
Transmission: 700R4
Axle/Gears: 3.23
Re: Loudes exhaust for a 84 z28
I strongly encourage you NOT to just go out and build the loudest exhaust you can. Search around youtube and try to see which exhaust system sounds the best to you, tone should be the more important factor, not sheer volume alone IMO
04-05-2012, 08:31 AM
#6
Re: Loudes exhaust for a 84 z28
Well, there's no hope for me. I am a classic case of arrested development. I have a flow pro on my IROC, but it's not loud enough for me. Sounds sweet though. If you want more sound, you can weld a y pipe on a glass pack in place of a standard 1 in 2 out muffler. This is if you want duel pipes out the rear. it will be nice and "loud", but will cut down on high frequency noise.
04-05-2012, 11:07 AM
#7
Member
iTrader: (4)
Join Date: Mar 2009
Location: Gonzales, LA
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 Camaro Z28
Engine: 5.7 TPI
Transmission: 700R4
Axle/Gears: 3.42
Re: Loudes exhaust for a 84 z28
Run a chambered powerstick in place of your Intermediate pipe and dump it after the axle.... That is what I did and it sounds sweeeeet... not very far off from sounding like a GMMG system.
Trending Topics
04-05-2012, 08:51 PM
#9
Member
iTrader: (4)
Join Date: Mar 2009
Location: Gonzales, LA
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 Camaro Z28
Engine: 5.7 TPI
Transmission: 700R4
Axle/Gears: 3.42
Re: Loudes exhaust for a 84 z28
The GMMG system uses two of these in its system. I personally only am using one medium length stick and trust me.... the neighbors are pissed...hehe
04-06-2012, 12:40 AM
#11
Member
Join Date: Oct 2011
Location: Ewing,New jersey
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 Berlinetta
Engine: 2.8
Re: Loudes exhaust for a 84 z28
why dont you just weld in some cutouts?
my mustang had shortie headers going to cutouts than flowmaster 40s and dumped before the axel sounded sweet and if you get tired of the obnoxious loud on the highway you can close the cutouts
my mustang had shortie headers going to cutouts than flowmaster 40s and dumped before the axel sounded sweet and if you get tired of the obnoxious loud on the highway you can close the cutouts
Thread
Thread Starter
Forum
Replies
Last Post
