Testa Rossa

iTrader: (1)

Far as I'm concerned, this car (83 camaro) is for scrap.

If you need replacement body panels for your rusty car or collision repair, I will cut any panel off my car and ship it to you (they can be picked up as well).

Want to make yours a T-Top?!? I'll cut off the roof!
Rear quarter panels? No problem

Floor boards, quarter panels, trunk "floor", inner and outer structural sheet metal... ANYTHING!


I will provide "standard" size sheet metal parts.
Entire quarter panels, doors, floorboard quarters (L/R F/R), or complete floorboard, etc.
I won't simply cut 12"x12" pieces (or others) unless it is for an area that's not normally available as a standard repair panel.

Will do my best to split seems rather than cut whenever possible.
Parts will be rough cut using an angle grinder.
Edges will not be cleaned up (or only minimally) prior to shipping

(I'll cut it right down it right down the middle and ship you half if you want!)

You pay ACTUAL shipping. I don't change a S&H premium, unless I have to buy "special supplies" that I don't otherwise have on hand. (for instance, if I had to "crate" a pat)

Most parts will not go over weight limit. Size of panel/package will be the primary limiting factor.
You can get a rough shipping quote simply by taking the measurements of the panel you want, and putting that into any shipping calculator (USPS, UPS, Fedex, DHL, etc). May need to add an inch or two to dimentions for packaging. If feasible, I will simply protect corners and sharp edges and wrap with plastic (the saran wrap stuff). It it needs extra protection, I will box it.
(I will try to keep the package as small as possible).

Just let me know what you need.


http://i8.photobucket.com/albums/a45...0Camaro%20Z28/

MassD

iTrader: (1)

How much for the driver side rear quarter panel shipped to 11010

Testa Rossa

iTrader: (1)

Send me a pic highlighting where you want it cut (from door jamb to rear bumper, or from the wheel-well back?)

The size of the package will probably be more of a factor than the weight. Might have to be shipped freight... (for instance, rockauto charges $168 freight just for shipping to CA)
Of course I'll shipp be the cheapest method (or any that you prefer).

RocVert

iTrader: (1)

How bout a drivers side front floorboard or floorpan
from right in front of the drivers seat mount and as far forward as you can go
maybe 4 inches up the tunnel on the right or more and as far over to the left as you can go toward the rocker.

Shipped to 55041 ? thanks

Testa Rossa

iTrader: (1)

I'll take some measurements and try to get you a quote today or tomorrow
(I can estimate the weight based on measurements, but it shouldn't be too much)

RocVert

iTrader: (1)

Thanks Man !

ya it shouldnt be too terrible size and weight wise hopefully for what chunk i need.

Let me know if you need some confirmation on where to cut, but from my description i think you get the jist.

Thanks again, and i am assuming these are rust free parts got any pics of the floorboards ?

Testa Rossa

iTrader: (1)

Didn't get a chance to pull all the junk out of the front to get exact measurements, but I tried to get close..

I estimated package size would be about 30" x 24" x 4" (plus or minus).
Flooring Sheet metal usually being 16-18 ga weighs about 2lbs per sq ft.
So I estimate the weight between 10 12 lbs.
didn't matter whether it was 10 or 12... package size determined shipping cost.
About $25 - $30 for USPS of UPS Ground receptively.

These MAY be a little on the low side, so it cCould go up a little bit if my weight or dimensions are off. (maybe $45-50 tops).

Rockauto charges $83 to ship theirs (full pan, not just front), but it definitely wouldn't be that much.


I wouldn't expect much rust from a Cali car.
Not much to speak of from underneath, but I'll peel back the carpet and try to snap a pic sometime this week if you like.

Trying to multitask... so please be patient with me. I'll get to it as soon as I can.

RocVert

iTrader: (1)

Np and thank you

83C_CamAroZ28

iTrader: (12)

I need a few pieces. I need a piece for the passenger side and a piece rite under the heater core rite next to the wheel. How's the ttops?

I can possibly pick up.

Testa Rossa

iTrader: (1)

So are we talking sheet metal panels, interior pieces or what?

(Getting a bit confused with cross-posting... )

T-tops are in good shape.
Weather stripping is pretty old and worn out but useable.
Everything else, is not too bad...


In any case... I should have everything you need.
Just might need some clarification (or pictures)

Testa Rossa

iTrader: (1)

How do you like this?!?!

ZERO RUST!!!

Paint is still glossy even!
Even underneath the car, there is no rust (but of course the paint isn't as pretty).

Measurements I gave you were pretty darn close!
I can go up the front of the firewall a little, or even to to the top of the tunner, but that would increase the height/thickeness to about 9 inches and increase shipping to about $60.

Let me know exactly how much you want and lets talk about price.
Feel free to shoot me a PM.

Testa Rossa

iTrader: (1)

Oh my bad.... that was a passenger side.... but driver side is the same!!

83C_CamAroZ28

iTrader: (12)

Pm'd u...

jerryramon2007

hi i am interested in the driver and passenger floor panels if the other guy hasn't snagged them yet. Thanks.

Testa Rossa

iTrader: (1)

Exchanging some PM's but no hard deals yet.

I charge actual shipping so it would be based off whatever the dimensions are. Weight would not really come into play. I'll try to measure and ge ta quote, but you can probably measure yours to get a rough idea.

Obviously it would be cheaper to cut it in half and ship together than one complete pan...

Testa Rossa

iTrader: (1)

Been pretty busy lately, but I'm goning to try to start cutting into it the next week or two. Still have a few more things to remove first. Might work on it a little this weekend.

Coolball

iTrader: (5)

How about the rocker ground effect for the passenger side do you have it?

Coolball

iTrader: (5)

Also interested in the turn signal/cruise control lever, is it a 3 wire?

Testa Rossa

iTrader: (1)

Sorry. Already gone.