Desperately Need Wiring Help!!
#1
Supreme Member
Thread Starter
iTrader: (7)
Join Date: Jun 2008
Location: Minnesota
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROC-Z
Engine: 370 LSX, LS3 Top End
Transmission: Built T-56
Axle/Gears: 9" Aluminum Center 3.89's
Desperately Need Wiring Help!!
OK, so this weekend I got some wiring done, but I don't know where to tap into to find these connections, and the hardest part about it all...i'm color blind. So finding colored wires is difficult to say the least!
This is what I need:
TPS, found
Tach, Found Location, but will the pcm be throwing a 4 cylinder signal or 8? I need to know for my autometer tach.
Oil pressure, Found the location in the gauge connector, but does that wire go directly to the sender? If it does i can use it, but if it doesn't i assume i can't tie that right into the autometer gauge
I took a bunch of pics, I really hope you guys can help me with this!
Old CLuster
1
2
3
4
In the above 2 pics, is any of those wires what i need? THey'd be the easiest to tap into.
Also, What the hell are these wires for?
5
6
7
I can't thank you guys enough!
This is what I need:
TPS, found
Tach, Found Location, but will the pcm be throwing a 4 cylinder signal or 8? I need to know for my autometer tach.
Oil pressure, Found the location in the gauge connector, but does that wire go directly to the sender? If it does i can use it, but if it doesn't i assume i can't tie that right into the autometer gauge
I took a bunch of pics, I really hope you guys can help me with this!
Old CLuster
1
2
3
4
In the above 2 pics, is any of those wires what i need? THey'd be the easiest to tap into.
Also, What the hell are these wires for?
5
6
7
I can't thank you guys enough!
Last edited by 89ROC-Z; 04-09-2012 at 01:12 PM.
#2
Supreme Member
Thread Starter
iTrader: (7)
Join Date: Jun 2008
Location: Minnesota
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROC-Z
Engine: 370 LSX, LS3 Top End
Transmission: Built T-56
Axle/Gears: 9" Aluminum Center 3.89's
Re: Desperately Need Wiring Help!!
Also, it'd be great to not have to tap into the red and blue connectors on the pcm, idk if i could get enough slack in the wires to cut, splice, and solder in there.
Where are these connectors and what do they look like?
c105, c220, c230,
Where are these connectors and what do they look like?
c105, c220, c230,
#3
Supreme Member
iTrader: (35)
Join Date: Aug 2006
Location: Mississauga,Ont,Canada
Posts: 1,470
Likes: 0
Received 1 Like
on
1 Post
Car: 89 IROC
Engine: LSX 6.0 370, TU2 Cam, Fast intake
Transmission: T56 w/ lots of goodies
Axle/Gears: 8.8, Posi, 4.10, 31 Spline
Re: Desperately Need Wiring Help!!
here is a pin out of the 2 dash cluster connectors. The wires are numbered as well so no worries on the colours for you. The only issue you might have is which side is the grey and which side is the clear/white side
#4
Supreme Member
Thread Starter
iTrader: (7)
Join Date: Jun 2008
Location: Minnesota
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROC-Z
Engine: 370 LSX, LS3 Top End
Transmission: Built T-56
Axle/Gears: 9" Aluminum Center 3.89's
Re: Desperately Need Wiring Help!!
Awesome!!!! Can't thank you enough man!
Quick question with the C1 13 pin (oil Pressure). Does that wire go through the PCM at all?
Quick question with the C1 13 pin (oil Pressure). Does that wire go through the PCM at all?
#5
Supreme Member
iTrader: (35)
Join Date: Aug 2006
Location: Mississauga,Ont,Canada
Posts: 1,470
Likes: 0
Received 1 Like
on
1 Post
Car: 89 IROC
Engine: LSX 6.0 370, TU2 Cam, Fast intake
Transmission: T56 w/ lots of goodies
Axle/Gears: 8.8, Posi, 4.10, 31 Spline
Re: Desperately Need Wiring Help!!
I used a autometer oil pressure sender that I attached to the oil filter housing. I try not to tap into lines as it adds to the electrical gremlins down the road.
#6
Supreme Member
iTrader: (24)
Join Date: Jun 2005
Location: NC
Posts: 7,901
Likes: 0
Received 92 Likes
on
56 Posts
Car: 92 Firebird
Engine: Supercharged 6.0
Transmission: T56
Axle/Gears: 8.8 3.73
Re: Desperately Need Wiring Help!!
Stock, the PCM outputs a 4cyl signal. This is supposed to be reset to 8cyl mode for swaps. Its a simple change either way
Oil pressure is direct from the sender to gauge
Only gauge wire in your C207 is MIL, but its easier to tap into from the old cluster connector
1st connector pic is cruise control from the stalk to the module harness under the dash
2nd pic with loose wires, I cant tell. Get a better pic of the surroundings and where it goes up under the dash
3rd is stock speaker wires
You shouldnt have to tap into the PCM wires to run aftermarket gauges. All wires except one can be found on your old cluster connectors. The remainder is for an electric speedo and can be found in the Cable-X bundle near your PCM, tagged speedo. Ignore the power and ground from the set
Oil pressure is direct from the sender to gauge
Only gauge wire in your C207 is MIL, but its easier to tap into from the old cluster connector
1st connector pic is cruise control from the stalk to the module harness under the dash
2nd pic with loose wires, I cant tell. Get a better pic of the surroundings and where it goes up under the dash
3rd is stock speaker wires
You shouldnt have to tap into the PCM wires to run aftermarket gauges. All wires except one can be found on your old cluster connectors. The remainder is for an electric speedo and can be found in the Cable-X bundle near your PCM, tagged speedo. Ignore the power and ground from the set
#7
Supreme Member
Thread Starter
iTrader: (7)
Join Date: Jun 2008
Location: Minnesota
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROC-Z
Engine: 370 LSX, LS3 Top End
Transmission: Built T-56
Axle/Gears: 9" Aluminum Center 3.89's
Re: Desperately Need Wiring Help!!
Stock, the PCM outputs a 4cyl signal. This is supposed to be reset to 8cyl mode for swaps. Its a simple change either way
Is this done simply with the tune?
Oil pressure is direct from the sender to gauge
Great, makes my life easier for that wire!
Only gauge wire in your C207 is MIL, but its easier to tap into from the old cluster connector
If I use a LED, do I ground the ground wire and run the 12v to the MIL wire? In the above diagrams, it says the stock pcm provides a ground when necessary
1st connector pic is cruise control from the stalk to the module harness under the dash
2nd pic with loose wires, I cant tell. Get a better pic of the surroundings and where it goes up under the dash
That's the other end of the 1st conntector/ cruise control.
3rd is stock speaker wires
You shouldnt have to tap into the PCM wires to run aftermarket gauges. All wires except one can be found on your old cluster connectors. The remainder is for an electric speedo and can be found in the Cable-X bundle near your PCM, tagged speedo. Ignore the power and ground from the set
Is this done simply with the tune?
Oil pressure is direct from the sender to gauge
Great, makes my life easier for that wire!
Only gauge wire in your C207 is MIL, but its easier to tap into from the old cluster connector
If I use a LED, do I ground the ground wire and run the 12v to the MIL wire? In the above diagrams, it says the stock pcm provides a ground when necessary
1st connector pic is cruise control from the stalk to the module harness under the dash
2nd pic with loose wires, I cant tell. Get a better pic of the surroundings and where it goes up under the dash
That's the other end of the 1st conntector/ cruise control.
3rd is stock speaker wires
You shouldnt have to tap into the PCM wires to run aftermarket gauges. All wires except one can be found on your old cluster connectors. The remainder is for an electric speedo and can be found in the Cable-X bundle near your PCM, tagged speedo. Ignore the power and ground from the set
Thread
Thread Starter
Forum
Replies
Last Post
Glowsock
Tech / General Engine
3
01-09-2017 04:06 PM
Hellbillydeluxe
Tech / General Engine
10
09-22-2015 09:58 PM