Where to pour Oil!!!
#1
Junior Member
Thread Starter
Join Date: Sep 2006
Location: CT
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Trans AM
Engine: 305 TPI 5.0L
Where to pour Oil!!!
I went out today spent around 58$ in filters and such and oil but i ran into a problem i pop open my hood and look in there is no spout for the oil pour in i see on the power steering in front with the belt hooked up (greenish Yellow color i see the dip stick for Oil then the dip stick for tranny but no spot that screams pour oil here. Sorry about this but im just damn confused.
Make Pontiac
Module: 1985 tpi T/A 305 5.0 V8 FI
Make Pontiac
Module: 1985 tpi T/A 305 5.0 V8 FI
#2
Supreme Member
iTrader: (1)
Join Date: Apr 2000
Location: Northern CA.
Posts: 5,321
Likes: 0
Received 4 Likes
on
4 Posts
Car: '82 Z28
Engine: 350
Transmission: TH400 4,000 stall
Axle/Gears: Currie 9", 4.56 gears
Stock valve covers should have an oil cap, they don't always necessarily say OIL. Since I don't have stock valve covers, I just remove the PCV valve and take my time pouring the oil through that hole into the valve cover.
#3
Which all reminds me of the old urban legend/tale about the novice service station attendant (Anyone remember those - People who actually pumped your gas, checeked your fluids, washed the windows, checked tires, etc.? ) after checking the oil and discovering it was a quart low, he added oil by pouring it all over the engine. The explanation was that "The entire engine needs oil, so I put it everywhere."
#4
Supreme Member
iTrader: (21)
Join Date: Dec 2005
Posts: 4,075
Likes: 0
Received 1 Like
on
1 Post
Car: 04 Silverado
Engine: 4.8
Transmission: auto
Which all reminds me of the old urban legend/tale about the novice service station attendant (Anyone remember those - People who actually pumped your gas, checeked your fluids, washed the windows, checked tires, etc.? ) after checking the oil and discovering it was a quart low, he added oil by pouring it all over the engine. The explanation was that "The entire engine needs oil, so I put it everywhere."
#5
Senior Member
iTrader: (4)
Join Date: Feb 2003
Location: shawnee, ks
Posts: 713
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Firebird
Engine: 5.3 76mm
Transmission: Rossler TH400, PTC converter
Axle/Gears: Strange 12bolt, 3.08s
Which all reminds me of the old urban legend/tale about the novice service station attendant (Anyone remember those - People who actually pumped your gas, checeked your fluids, washed the windows, checked tires, etc.? ) after checking the oil and discovering it was a quart low, he added oil by pouring it all over the engine. The explanation was that "The entire engine needs oil, so I put it everywhere."
#6
Junior Member
Thread Starter
Join Date: Sep 2006
Location: CT
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Trans AM
Engine: 305 TPI 5.0L
gave up on changing the oil today when spending about 45 mins trien to get the oil pan bolt off so i finished off setting up the intake.
anypointers on getting stuborn bolt to move?
anypointers on getting stuborn bolt to move?
Trending Topics
#8
Member
Join Date: Mar 2006
Location: KC. KS
Posts: 357
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 Firebird
Engine: 408
Transmission: 700r4
Axle/Gears: 12 bolt/4.11
Which all reminds me of the old urban legend/tale about the novice service station attendant (Anyone remember those - People who actually pumped your gas, checeked your fluids, washed the windows, checked tires, etc.? ) after checking the oil and discovering it was a quart low, he added oil by pouring it all over the engine. The explanation was that "The entire engine needs oil, so I put it everywhere."
#9
Member
Join Date: Jul 2006
Location: Lincoln, Nebraska
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Trans Am
Engine: Mild 10:1 355.
Transmission: T-5
Axle/Gears: 9 bolt
idk if this kid is being dumb on purpose or not, but um.. yea,
Cap - on - valve - cover
turn it
pull off
pour oil in
put cap back in
tighten
Cap - on - valve - cover
turn it
pull off
pour oil in
put cap back in
tighten
#11
Junior Member
Thread Starter
Join Date: Sep 2006
Location: CT
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Trans AM
Engine: 305 TPI 5.0L
+++ Sigh i ment the oil pan drain plug
as for the intake was just finishing up installing the duct part as my car didn't have one to start with.
#12
Supreme Member
iTrader: (2)
Join Date: Sep 2003
Location: Woodland, CA
Posts: 10,494
Likes: 0
Received 3 Likes
on
3 Posts
Car: '02 Z06
Engine: L33 5.7
Transmission: T56
Axle/Gears: Stock IRS
I would just drill a hole in your oil pan next to the bolt, and when you are done, Tighten a screw into your newly aquired hole to prevent leaks.
#13
Member
iTrader: (1)
Join Date: Jan 2006
Location: Texas
Posts: 369
Likes: 0
Received 0 Likes
on
0 Posts
Car: '68 396 SS/RS, '02 SS
So you spent 45 minutes trying to get the drain plug out and still didn't I gather, and don't know where to put the oil back in once you get the old oil out. So you decided to "set up the intake" instead.
I'm the one confused!
I'm the one confused!
#15
Junior Member
Thread Starter
Join Date: Sep 2006
Location: CT
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Trans AM
Engine: 305 TPI 5.0L
sigh...
Well to help Clear things up i bought this car from a junk yard the car was stripped and also modified engine wise when i get my film devolped i'll post some before and after pics.
Here is the pic of the valve covers that are installed I know there Chevy but they got them to fit some how this is why i asked the question where to pour the oil. Edelbrock Classic Cast Aluminum Valve Covers: EDL-4145 - summitracing.com
As for the intake i was worken on the whole setup was missing filter, box, Maf, and ductwork
As for the drain plug the car was last driven in june of 99
(no frame rot only major thing was interior is shot)
I hope this clears up some confusion.
Well to help Clear things up i bought this car from a junk yard the car was stripped and also modified engine wise when i get my film devolped i'll post some before and after pics.
Here is the pic of the valve covers that are installed I know there Chevy but they got them to fit some how this is why i asked the question where to pour the oil. Edelbrock Classic Cast Aluminum Valve Covers: EDL-4145 - summitracing.com
As for the intake i was worken on the whole setup was missing filter, box, Maf, and ductwork
As for the drain plug the car was last driven in june of 99
(no frame rot only major thing was interior is shot)
I hope this clears up some confusion.
#17
Moderator
iTrader: (57)
Join Date: Sep 2000
Location: Annapolis Maryland
Posts: 1,149
Likes: 0
Received 14 Likes
on
12 Posts
Car: To many to list
85 wouldnt have centerbolts anyway.Those valve covers are for the early chevys,when they had the oil fill through the intake.I dont know what to tell you without a pic,but you may need some new valvecovers .02
#18
Supreme Member
Join Date: Jul 2005
Location: Arab, Alabama
Posts: 1,675
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1988 Trans Am GTA
Engine: 350 4BBL
Transmission: 700R4
Axle/Gears: 3.27
Now see there, Y'all play nice. The previous owner obviously put on some very nice ribbed "pre-1968" valve covers on a 82-87 engine.
I think they're too pretty to throw away too.
So, if your 82-87 engine suddenly had these valve covers on it, what would you do to put oil in the engine?
This is a brain teaser for all of the smart people out there.
And don't even talk about the PCV, like where would the blowby come out?
Alright smart people...are you>
I think they're too pretty to throw away too.
So, if your 82-87 engine suddenly had these valve covers on it, what would you do to put oil in the engine?
This is a brain teaser for all of the smart people out there.
And don't even talk about the PCV, like where would the blowby come out?
Alright smart people...are you>
#19
Member
Join Date: Dec 2003
Location: So. Illinois
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
Car: '93 S10 Short bed standard cab
Engine: 383 Stroker
Transmission: 92' stage 2 700r4 w/3600 stall
Axle/Gears: 3.42
Now see there, Y'all play nice. The previous owner obviously put on some very nice ribbed "pre-1968" valve covers on a 82-87 engine.
I think they're too pretty to throw away too.
So, if your 82-87 engine suddenly had these valve covers on it, what would you do to put oil in the engine?
This is a brain teaser for all of the smart people out there.
And don't even talk about the PCV, like where would the blowby come out?
Alright smart people...are you>
I think they're too pretty to throw away too.
So, if your 82-87 engine suddenly had these valve covers on it, what would you do to put oil in the engine?
This is a brain teaser for all of the smart people out there.
And don't even talk about the PCV, like where would the blowby come out?
Alright smart people...are you>
Last edited by krly79; 10-15-2006 at 08:19 PM.
Thread
Thread Starter
Forum
Replies
Last Post
bigjay89gta
Engine/Drivetrain/Suspension Parts for Sale
12
10-15-2015 08:04 AM
skinny z
Engine/Drivetrain/Suspension Parts for Sale
5
10-05-2015 06:23 PM