Third Generation F-Body Message Boards

Search: Posts Made By: gmonly
Showing results 1 to 24 of 24
Search took 0.05 seconds.
Forum: Transmissions and Drivetrain
11-01-2011, 09:37 PM
Replies: 44
Important/Useful : Th400 parts list.
Views: 53,423
Posted By gmonly

Re: Th400 parts list.

this is the site for a new Speed Sensor, scroll down the page:

http://www.transmissioncenter.net/speedometer_calibration_______va.htm

you are welcome
...
Forum: Transmissions and Drivetrain
11-01-2011, 12:37 AM
Replies: 44
Important/Useful : Th400 parts list.
Views: 53,423
Posted By gmonly

Re: 700R4 Transmission Problem

you can get a Speed Sensor at a salvage yard or new, i seen a website posted in these forms, just do not remember where, it was about vss. from the looks of it, the seals (o-rings) are shot. for that...
Forum: Transmissions and Drivetrain
10-19-2011, 11:50 PM
Replies: 44
Important/Useful : Th400 parts list.
Views: 53,423
Posted By gmonly

Re: Th400 parts list.

measure both tail shafts, yours might be a 6 inch. if that is the case, you would need to cut the drive shaft and doing what i had to do. best bet would be to look for a short tail shaft th350/375...
Forum: Electronics
06-19-2010, 09:31 PM
Replies: 9
Views: 617
Posted By gmonly

Re: Any Ideas on getting headlights up??

that will still be a lot of force, the j b weld will not hold the pressure.
Forum: Transmissions and Drivetrain
06-16-2010, 09:29 AM
Replies: 8
Views: 2,651
Posted By gmonly

Re: Loose transmission crossmember problem

i just drilled on the side as close i could where the nut was by looking. i have run across this a few times so far.
Forum: Transmissions and Drivetrain
06-15-2010, 10:49 PM
Replies: 7
Views: 459
Posted By gmonly

Re: tranny problem need help

disconnect the battery for about 10 minutes, that will clear the codes. see if it helps, if there is something wrong, the code will come back.
i do not think another pcm would work right, they are...
Forum: Transmissions and Drivetrain
06-15-2010, 09:22 PM
Replies: 8
Views: 2,651
Posted By gmonly

Re: Loose transmission crossmember problem

as long as the nut(s) does not turn, drill and tap would work. i just have not been that lucky, so i had to make the wrench whole.
Forum: Transmissions and Drivetrain
06-15-2010, 01:20 AM
Replies: 3
Views: 1,805
Posted By gmonly

Re: Clutch won't go down now!

sorry, i meant throwout bearing, not pilot bearing. i was preoccupied when i typed that (a phone call).
to me it sounds like the throwout bearing is in wrong, check that out first.
Forum: Transmissions and Drivetrain
06-14-2010, 11:04 PM
Replies: 7
Views: 1,912
Posted By gmonly

Re: TV Cable adjustment issue???

did it work before?
if it did, check to see if it came apart in the trainy end.
if it has not worked before, it looks like the bracket is not far enough back from the carb.
also, is the cable...
Forum: Transmissions and Drivetrain
06-14-2010, 10:56 PM
Replies: 3
Views: 1,805
Posted By gmonly

Re: Clutch won't go down now!

is the pilot beering in right? sounds to me, it might have either been put in wrong or it fell out of the hlding clip.
Forum: Transmissions and Drivetrain
06-14-2010, 10:45 PM
Replies: 8
Views: 2,651
Posted By gmonly

Re: Loose transmission crossmember problem

i have cut a hole on the inside big enough for a wrench, then put a nut on (i used duck tape to hold the nut to the wrench). it did not hurt the stuctural integrity of the frame.
Forum: Transmissions and Drivetrain
06-14-2010, 10:16 PM
Replies: 2
Views: 590
Posted By gmonly

Re: rear end help please

i had about the same problem, the shimes was worn thin and in the bottom along with a lot of metal slivers, also the pin on the driver side was broke in half. i found a posi 3.73 in the salvage yard,...
Forum: Transmissions and Drivetrain
06-13-2010, 10:50 PM
Replies: 7
Views: 459
Posted By gmonly

Re: tranny problem need help

his code reader is probably a obd2 (96 and up), you need a obd1 code reader (95 and older)
Forum: Transmissions and Drivetrain
06-12-2010, 01:51 PM
Replies: 7
Views: 459
Posted By gmonly

Re: tranny problem need help

what is the trouble code(s), that will help some
Forum: Electronics
06-12-2010, 01:04 PM
Replies: 59
Views: 78,422
Posted By gmonly

Re: electronic speedo to cable speedo?

an update on my trainy problem.

it now upshifts at about 5000 rpms, once it is in 3rd, i have to keep my foot on the pedal or it slows down fast. i ordered the right speedo gears and had a 700r4...
Forum: Transmissions and Drivetrain
06-10-2010, 09:01 PM
Replies: 9
Views: 9,472
Posted By gmonly

Re: 700r4 only working in first and reverse

i went from a 700r4 to a th400 long tail. i had to relocate my trainy cross member, change trainy mount, get a vaccume port for the intake for the modulor. i just got a new modulor and half a govener...
Forum: Electronics
06-10-2010, 08:23 PM
Replies: 59
Views: 78,422
Posted By gmonly

Re: electronic speedo to cable speedo?

it does not up shift till about 7500 to 9000 rpms, the 1-2 shift is at about 50 mph, the 2-3 is the same for rpms but at about 80 mph, it idles fine and when i let off the throttle, it idles normal...
Forum: Transmissions and Drivetrain
06-10-2010, 07:53 PM
Replies: 9
Views: 9,472
Posted By gmonly

Re: 700r4 only working in first and reverse

that is a bummer. either you put more money in that trainy or get the th350. now you have a coin toss, i pick heads :)
Forum: Transmissions and Drivetrain
06-10-2010, 07:07 PM
Replies: 9
Views: 9,472
Posted By gmonly

Re: 700r4 only working in first and reverse

i would go with a th350. i have had nothing but badd luck with the 700r4's. i had a th400 setting around, so i used that, it is a lot more work then the th350 would be.
Forum: Electronics
06-10-2010, 11:07 AM
Replies: 59
Views: 78,422
Posted By gmonly

Re: electronic speedo to cable speedo?

that is a lot of money for that part. i am retired, and can not afford that right now.

there should be a part like in post 20 that would work.
if not, i will just get the tail shaft housing...
Forum: Transmissions and Drivetrain
06-09-2010, 04:58 PM
Replies: 13
Views: 24,118
Posted By gmonly

Re: 700R4 shifts hard into D and Reverse from Park

there should be a screw on the front right side of the TB, it might have a cap covering the hole the screw is in. look on the front side where the throtle is.
you might need a carb adjusting...
Forum: Transmissions and Drivetrain
06-09-2010, 04:34 PM
Replies: 5
Views: 10,941
Posted By gmonly

Re: Auto Transmission shifting Late/hard??

does it have a modulator on the pass side of the trainy? if it does, check the vaccume line (rubber ends). if they are connected and not cracked, the vaccume mod might be bad.
Forum: Transmissions and Drivetrain
06-09-2010, 03:16 PM
Replies: 44
Important/Useful : Th400 parts list.
Views: 53,423
Posted By gmonly

Re: Th400 parts list.

bad88_milldawg, look in the full size vans and the 95 and up 4x4 pickups. their driveshafts should be about the size you need. i took a 700r4 out and put in a th400 long output shaft in a 1500 extend...
Forum: Electronics
06-09-2010, 12:05 AM
Replies: 59
Views: 78,422
Posted By gmonly

Re: electronic speedo to cable speedo?

this is all odd, i have had 6@ 700r4 trainys, from 87 to 91, every one of them have had the metal gear in them. long story short - i put a th400 in. tired of them 700r4's not lasting for hulling a...
Showing results 1 to 24 of 24


 
Forum Jump


All times are GMT -5. The time now is 03:50 AM.