Third Generation F-Body Message Boards

Search: Posts Made By: eddie79
Showing results 1 to 18 of 18
Search took 0.06 seconds.
Forum: Transmissions and Drivetrain
03-24-2012, 10:25 PM
Replies: 3
Views: 5,703
Posted By eddie79

Re: 700r4 overdrive shudder?

I'm not sure. today i put a derales tranns cooler in it, ran a hot wire to tc lock up wire. it stays hot all time unless i hit the brake. so thats workin rite. 13.9v. Idid notice that it didnt happen...
Forum: Transmissions and Drivetrain
03-22-2012, 09:02 PM
Replies: 3
Views: 5,703
Posted By eddie79

700r4 overdrive shudder?

Ive gotta 355 alotta mods done to it, w/ holley 750 ultra dp. my trans is a raptor 700r4 by PATC, w/ a Hughes 3000 stall lockup. its built w/ billet& hardened parts. its all new, shifts fine BUT...
Forum: Carburetors
12-10-2011, 08:29 AM
Replies: 28
Views: 1,389
Posted By eddie79

Re: My first engine build. Carb questions I guess...

w/ a 525 lift cam your gonna need more intial timing, usually 16-20 intial is gonna be rite. and you want the mech to start moving rite off idle immedietly. but it needs to be all in 3000 rpm or so.
Forum: Carburetors
12-10-2011, 08:12 AM
Replies: 9
Views: 25,012
Posted By eddie79

Re: quadrajet choke wire

just like installing any after market carb w electric choke it needs 12v. DO NOT HOOK IT TO THE DISTRIBUTOR ITS ONLY 9 VOLTS!!. it wont work right. holley recommends your windshield wiper motor, its...
Forum: Carburetors
12-10-2011, 08:04 AM
Replies: 11
Views: 15,570
Posted By eddie79

Re: holley fuel pressure regulator problems

heres the problem, the tbi in the tank is way too much pressure for a carb. I had same thing. theres only 1 pressure regulator that summitt racing sells I think its a mallory that will regulate from...
Forum: Tech / General Engine
12-10-2011, 07:36 AM
Replies: 12
Views: 924
Posted By eddie79

Re: looking for some carb/cam/intake advice for my engine

Also I would recommend a edlbrock rpm intake its good for street manners. you should consider upgrading your dist- setup too. a nite and day differnce w/ a new carb, intake and dist! just did this...
Forum: Tech / General Engine
12-10-2011, 07:31 AM
Replies: 12
Views: 924
Posted By eddie79

Re: looking for some carb/cam/intake advice for my engine

to reply on the carb section i would definitly go w/ a holley. there are way more parts availble for tuning and rebuilding than other companys. a 650 cfm is gonna give you better throttle response, a...
Forum: Tech / General Engine
12-08-2011, 08:15 PM
Replies: 11
Views: 2,959
Posted By eddie79

Re: Oil Pump Priming: Conflicting Opinions

to prime your motor before intial start up, you need to make sure that the primer is clamped down w/ the dist clamp on top of intake. And go to drillin. dependin on type of oil sum will catch prime...
Forum: Transmissions and Drivetrain
12-06-2011, 07:38 PM
Replies: 5
Views: 1,130
Posted By eddie79

Re: Cadillac 700r4 into 1991 Camaro?

somethin that comes off the top of my head is ( I didnt read your 1st art.) while your out lookin for another 700r you should try to get a 30 spline 700r4. that is the newest model they made before...
Forum: Tech / General Engine
12-05-2011, 07:09 PM
Replies: 19
Views: 7,749
Posted By eddie79

Re: STRONG Exhaust Fumes.

I dont have a air fuel monitor/ gauge on it, I have the o2 bund already welded to the header just have to drill the hole. that mite be my next lil project. My wife loves the car but she wont even...
Forum: Transmissions and Drivetrain
12-05-2011, 06:52 PM
Replies: 1
Views: 747
Posted By eddie79

Torque arm bushings which ones right?

I got to replace the torque arm bushing on a 91 camaro rs, Anybody know which ones I would need? lips facing in - out idk!
Forum: Tech / General Engine
12-05-2011, 06:44 PM
Replies: 19
Views: 7,749
Posted By eddie79

Re: STRONG Exhaust Fumes.

That is a really good article. I wish Icould of read that about 1-1/2 yrs ago, i can honestly say I done everything they did about 99.9% of it. the car idles at 700rpm in gear. same for park...
Forum: Tech / General Engine
12-04-2011, 10:20 AM
Replies: 5
Views: 1,607
Posted By eddie79

Re: comp cams mother thumper

thats true, I've been through 3 hyd flat tap cams - comp,lunati, and crane blue racer which was a dam good cam 488 510 lift. let my bro inlaw drive took it past rpm and flatten lifter. so I decided...
Forum: Tech / General Engine
12-03-2011, 08:45 PM
Replies: 5
Views: 1,607
Posted By eddie79

comp cams mother thumper

I'm running the retrofit mother thumper roller cam, Just wondering if anybody else had tried this cam and what they thought of it. with my set up it has plenty of power. but I have low manifold vac....
Forum: Tech / General Engine
12-03-2011, 07:44 PM
Replies: 19
Views: 7,749
Posted By eddie79

Re: STRONG Exhaust Fumes.

that is sumthin i need to check. I put a new intake, holley carb, and distr on it awhile back. the vac gauge reads fairly steady within 1- 1 1/2" .but that much cam its gonna do that. whats the best...
Forum: Tech / General Engine
12-03-2011, 01:56 PM
Replies: 19
Views: 7,749
Posted By eddie79

Re: STRONG Exhaust Fumes.

yup I thought the same, if the rain holds up I'll try go at it again!!
Forum: Tech / General Engine
12-03-2011, 08:53 AM
Replies: 19
Views: 7,749
Posted By eddie79

Re: STRONG Exhaust Fumes.

im using a msd probillet w/ no vac adv. i was using a hei vac adv. still had same prob.
comp cams said intial should be 16-19, im @ 19.total is 32-33deg. The plugs look good, I did sum fine tuning...
Forum: Tech / General Engine
12-02-2011, 08:40 PM
Replies: 19
Views: 7,749
Posted By eddie79

STRONG Exhaust Fumes.

So I got a 91 rs, 355 .0040 over 2.02 041 heads street ported,rpm intake w/ holley ultra 750 dpump msd dig 6 ignition. cam specs r 511 522? mother thumper retrofit roller cam. when I stand behind the...
Showing results 1 to 18 of 18


 
Forum Jump


All times are GMT -5. The time now is 03:19 PM.