Third Generation F-Body Message Boards

Search: Posts Made By: RaCeCaRdRiVa
Showing results 1 to 14 of 14
Search took 0.11 seconds.
Forum: Tech / General Engine
10-26-2004, 12:44 PM
Replies: 4
Views: 2,733
Posted By RaCeCaRdRiVa

I went to Sears today and found the tool I...

I went to Sears today and found the tool I needed. It's a Craftsman 6 pc. Roll Pin Punch Set (Model #43167). I only needed the 5/32" Roll Pin Punch, but they sell them in a set of 6. They're like...
Forum: Tech / General Engine
10-25-2004, 11:14 PM
Replies: 4
Views: 2,733
Posted By RaCeCaRdRiVa

I'm going to buy a set of punches tomorrow...

I'm going to buy a set of punches tomorrow because my selection is limited. Is there a particular size punch or nail set that works best?
Forum: Tech / General Engine
10-25-2004, 07:39 PM
Replies: 4
Views: 2,733
Posted By RaCeCaRdRiVa

How to remove pin from distributor

I'm replacing the magnetic pickup coil in my distributor. In order to do this I must remove the pin at the base of the distributor below the gear. I've attempted to remove it, but it won't budge. ...
Forum: Aftermarket Product Review
08-07-2003, 02:52 AM
Replies: 1
Views: 663
Posted By RaCeCaRdRiVa

TPI Fuel Pressure Regulator

What is the best fuel pressure regulator for TPI? Has anybody had a good/bad experience with any of them?
Forum: Body
07-25-2003, 12:50 AM
Replies: 1
Views: 721
Posted By RaCeCaRdRiVa

Where can I find a spoiler like this?

Where can I find a spoiler like this?

http://images.cardomain.com/member_img_a/390000-390999/390038_19_full.jpg
Forum: Tech / General Engine
07-24-2003, 01:01 PM
Replies: 1
Views: 1,474
Posted By RaCeCaRdRiVa

Harmonic Balancer/Damper for Crate Engine

I'm swapping my LB9 (305 w/ TPI) for GM's 350 H.O. What kind of harmonic balancer would you guys recommend?
Forum: Body
07-22-2003, 11:01 PM
Replies: 6
Views: 552
Posted By RaCeCaRdRiVa

Triple Guage Pod (Where can I find one?)

Does anybody know where I can get a triple guage pod like the one pictured below?

http://ebay2.ipixmedia.com/abc/M28/_EBAY_d8b41f2896dbbab75b4906c58a8849fc/i-1.JPG
Forum: Exhaust
03-26-2003, 03:03 PM
Replies: 4
Views: 502
Posted By RaCeCaRdRiVa

Make sure you get HEI plug wires! Both ends...

Make sure you get HEI plug wires! Both ends should have 90 degree boots! Edelbrock's TES Headers don't give you a lot of clearance for the spark plugs or spark plug wires. Watch out for those air...
Forum: Exhaust
03-25-2003, 11:09 PM
Replies: 4
Views: 502
Posted By RaCeCaRdRiVa

I have Edelbrock TES Headers (w/ air injection)...

I have Edelbrock TES Headers (w/ air injection) on my 1986 IROC. My stock length wires ran too close to the headers and two of them melted, so I bought Accel's 300+ Wires. The kit was universal and...
Forum: Aftermarket Product Review
07-23-2002, 01:11 AM
Replies: 16
Views: 1,603
Posted By RaCeCaRdRiVa

:burnout: I installed Edelbrock's TES...

:burnout:

I installed Edelbrock's TES header system on my 1986 IROC! They came complete with air injection hookups, oxygen sensor hookup, and y pipe for just over $300. I ordered through...
Forum: Aftermarket Product Review
07-23-2002, 12:37 AM
Replies: 21
Views: 2,059
Posted By RaCeCaRdRiVa

Hey AdmiralNahohkta!!!!!

:burnout:

I was interested in purchasing a 350HO from GM. Does anybody know if the TPI from an 1986 IROC will work on this engine? I know I'll need a new manifold for the vortec heads. The...
Forum: Engine Swap
07-23-2002, 12:21 AM
Replies: 3
Views: 444
Posted By RaCeCaRdRiVa

We're in the same boat!

:burnout:

A 305 and a 350 Block are essentially the same size. You shouldn't have any problems interchanging the two.

We're in the same boat! I'm currently looking into swapping the engine...
Forum: Engine Swap
07-23-2002, 12:07 AM
Replies: 4
Views: 2,231
Posted By RaCeCaRdRiVa

Is 1986 an odd year for TPI?

:burnout:

Thank you for your input RICH92RS350!

The reason I started this thread is because I believe 1986 TPI manifolds and 1987 TPI manifolds are slightly different. Isn't 1987 the turning...
Forum: Engine Swap
07-22-2002, 01:40 AM
Replies: 4
Views: 2,231
Posted By RaCeCaRdRiVa

GoAutoCenter.Com TPI Engine (Engine swap)

:burnout:

This seems to be a redundant topic on Thirdgen.Org, but I'm doing a 305 --> 350 swap.

I have an '86 IROC with Tuned Port Injection (TPI).

I was interested in purchasing the 300 hp...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 12:47 AM.