Third Generation F-Body Message Boards

Search: Posts Made By: larry h
Showing results 1 to 14 of 14
Search took 0.13 seconds.
Forum: Electronics
05-01-2003, 12:54 PM
Replies: 4
Views: 407
Posted By larry h

it seems I had a similar problem on my 87 Iroc ...

it seems I had a similar problem on my 87 Iroc

Although I was concerned with the heater blower motor
same fan and switch though eh

sometime it would work , sometime not, then not at all

I...
Forum: Electronics
04-30-2003, 11:16 AM
Replies: 2
Views: 534
Posted By larry h

http://www.geocities.com/vtcamaro/Pictures/wiring-...

http://www.geocities.com/vtcamaro/Pictures/wiring-diagrams/pg220.jpg

this might be of some help
Forum: TPI
08-15-2002, 03:15 PM
Replies: 22
Views: 596
Posted By larry h

Davecs1 Good point, first the ECM swap and...

Davecs1

Good point, first the ECM swap and go from there !

thank you
Forum: TPI
08-15-2002, 02:15 PM
Replies: 22
Views: 596
Posted By larry h

it was bout 80 outside yesterday when I was...

it was bout 80 outside yesterday when I was working on it.

It is a MAF system

The distributor info will be real useful , thank you

I will provide update

thanks again everyone !!
Forum: TPI
08-15-2002, 02:05 PM
Replies: 22
Views: 596
Posted By larry h

it was worth askin, but I did check all the fuses...

it was worth askin, but I did check all the fuses under dash, they all tested good with a meter.

I did not test the positive lead on fuel pump relay, I will figure out which is the + and test...
Forum: TPI
08-15-2002, 01:24 PM
Replies: 22
Views: 596
Posted By larry h

Well looks like I am on a mission then ! I...

Well looks like I am on a mission then !

I will purchase a new ECM, and check all wiring looking for a short
before installation.

unless anyone has any further suggestions, I would like to...
Forum: TPI
08-15-2002, 01:15 PM
Replies: 22
Views: 596
Posted By larry h

So the memcal is the "chip" I pulled out, and the...

So the memcal is the "chip" I pulled out, and the ECM is the main box correct ?

Can you give me a guess as to why the ECM would have fried (if it is) , like I said before it was running, I shut it...
Forum: TPI
08-15-2002, 12:39 PM
Replies: 22
Views: 596
Posted By larry h

I had to remove a metal plate to get at it...

I had to remove a metal plate to get at it secured with 2 screws
Forum: TPI
08-15-2002, 12:37 PM
Replies: 22
Views: 596
Posted By larry h

I pulled the chip (wide chip with the little tabs...

I pulled the chip (wide chip with the little tabs on both sides) out of the main computer box, and left the box plugged in.
Forum: TPI
08-15-2002, 12:22 PM
Replies: 22
Views: 596
Posted By larry h

Well looks like it sucks to be me ! :( I...

Well looks like it sucks to be me ! :(

I went home at lunch, changed out fuel pump relay, that did not help, still does not start, and the fuel pump does not prime the system.

I also pulled...
Forum: TPI
08-15-2002, 11:20 AM
Replies: 22
Views: 596
Posted By larry h

Thanks for the suggestions guy's I will...

Thanks for the suggestions guy's

I will change fuel pump relay, and pull chip from ecm and look for fan operation.

I will be back with an update after lunch :)
Forum: TPI
08-15-2002, 11:04 AM
Replies: 22
Views: 596
Posted By larry h

Ok so your saying I might want to check or...

Ok so your saying I might want to check or replace the fuel pump relay, and or the backup relay (didnt know there was a "backup relay"

Would the relay work from my 85 then ? just to see if that is...
Forum: TPI
08-15-2002, 10:50 AM
Replies: 22
Views: 596
Posted By larry h

ah humor I love it ! yes you are correct...

ah humor I love it !

yes you are correct 305 was stock in the 85 Iroc I remove engine from, however it was replaced with a remanufactured 350
before I purchased.

No I do not hear the fuel...
Forum: TPI
08-15-2002, 10:06 AM
Replies: 22
Views: 596
Posted By larry h

87 tpi engine wont start please make suggestions

Gentlemen

Please let me start by saying I have been following this board for some time now and all of you have been very helpful, this is the first time I have found the need to post myself, but I...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 05:54 PM.