Third Generation F-Body Message Boards

Search: Posts Made By: Tim C
Showing results 1 to 24 of 24
Search took 0.02 seconds.
Forum: Tech / General Engine
01-20-2019, 03:25 PM
Replies: 3
Views: 859
Posted By Tim C

Re: Serpentine power steering bracket question

Thanks. I've got both those bar braces, one on the alternator to exhaust and another from the ac compressor to exhaust. Just wasnt sure if there was one on the back of the pump too that I may have...
Forum: Tech / General Engine
01-19-2019, 08:04 PM
Replies: 3
Views: 859
Posted By Tim C

Serpentine power steering bracket question

Was there a bracket on the back of the power steering pump that attached to the block or exhaust on a 91-92 tbi serpentine belt setup? When we parted out my brother's old 92 rs we used the...
Forum: DIY PROM
09-20-2017, 09:29 AM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Its a ramjet 350 crate engine so its basically a 9.4:1, iron vortec headed 99 chevy truck engine with 1.6 rockers and the ramjet manifold. I swapped the ramjet cam out for an lt4 hot cam but...
Forum: DIY PROM
09-19-2017, 08:25 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Well I have a final follow up. I lowered the AE-TPS coolant factor for pulse width factor table pretty significantly below 133*F basically its flat from 25*F to over 200*f now. That seems to have...
Forum: DIY PROM
08-13-2017, 05:47 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

I thought I'd bump this back up with a follow up and one more small question.

First, I didn't get an email notification for some reason so I didnt see you had responded Fast355. At any rate the...
Forum: DIY PROM
07-04-2017, 11:46 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Post the tables if you dont mind. Ill compare it to what im working with and see if it helps.

Thanks again.
Forum: DIY PROM
07-04-2017, 10:52 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Alright, I drove this thing Sunday afternoon and the VE tables seem to be decent. I burned another chip using the info from my datalog and the second test drive just seems to be bouncing the blms...
Forum: DIY PROM
07-02-2017, 10:10 AM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Ive been driving and datalogging for a week now. The miniram start bin was a great start off point for me. It was a bit rich, blms were in the 108 to 115 range initially. It took two 30 minute...
Forum: DIY PROM
06-24-2017, 09:09 PM
Replies: 5
Views: 902
Posted By Tim C

Re: Cant get data aquisition to work with TunerproRT v5

Yea, that's the same thing I show other than the com port number, which is to be expected.

At this point I'm going to start datalogging with my homemade two transistor cable. I'll call the cable...
Forum: DIY PROM
06-24-2017, 11:12 AM
Replies: 5
Views: 902
Posted By Tim C

Re: Cant get data aquisition to work with TunerproRT v5

Just a quick update. I removed all the ftdi usb and port related drivers I could find on device manager this morning, even the hidden inactive ones. I rebooted the laptop, and manually installed the...
Forum: DIY PROM
06-22-2017, 10:18 PM
Replies: 5
Views: 902
Posted By Tim C

Cant get data aquisition to work with TunerproRT v5

So I've done quite a good bit of datalogging on TBI computers using a homemade cable and a radioshack usb to serial convertor, but it was always glitchy and would disconnect randomly on both my old...
Forum: DIY PROM
06-11-2017, 08:24 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

That was my next step, I brought my nice fuel pressure gauge home from work this weekend and it's got a steady 45 psi with fuel pump relay jumpered engine off, the ramjet is supposed to have 24 #/hr...
Forum: DIY PROM
06-11-2017, 07:08 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Just to follow back up in case anyone searches this out in the future, I put a new eeprom 27sf512 on a memcal from a 7427 TBI PCM with the jumper installed just like the v6 to v8 memcal mod. It...
Forum: DIY PROM
04-22-2017, 10:34 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Thanks again ULTM8Z. It's going to be a little while before I make use of the bin, I've still got to get the truck here and get the old 283 out of it and the ramjet out of the camaro, but I'll poke...
Forum: DIY PROM
04-22-2017, 02:00 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Appreciate the help. I'll start gathering parts for the swap. We're waiting for the title to come back on the truck before we pick it up, so far just left a deposit to hold it. Not too worried...
Forum: DIY PROM
04-21-2017, 02:06 PM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Thanks RBob. I may try the 7427 Memcal I have extra. If it doesnt let any magic smoke out then worse case I may just have to cut a jumper and it'll still work in my TBI 7427. If it works then it's...
Forum: DIY PROM
04-21-2017, 11:16 AM
Replies: 28
Views: 2,248
Posted By Tim C

Re: 7730 for a RamJet 350 swap

Thanks ULTM8Z. I assume the miniram start bin stuff is on your website linked in your signature? If so I will check that out tonight after work. That was my biggest worry, actually. Questions 1-3...
Forum: DIY PROM
04-20-2017, 10:02 PM
Replies: 28
Views: 2,248
Posted By Tim C

7730 for a RamJet 350 swap

Backstory:

Back in 2001 or so we swapped a ramjet 350 crate engine into my brothers 92 RS Camaro in place of the stock 3.1. Fast forward to 2017 and he's bought a 15 Camaro and given the RS to my...
Forum: DIY PROM
02-05-2017, 12:43 PM
Replies: 1
Views: 652
Posted By Tim C

$0d TBI with MAF Cold start tuning

I have a 78 F150 with a stock rebuilt 351M I use offroad (rockcrawling). I originally swapped the stock two barrel carb to the 7747 setup from a 89 C1500 with a 5.7. A few years ago I did a 7427...
Forum: DIY PROM
02-13-2014, 11:06 PM
Replies: 12
Views: 2,142
Posted By Tim C

Re: $0d TBI MAF setup questions

Thanks. Any help is appreciated. Not sure if its a typo on your post but my computer is a 7427 not a 7727.
Forum: DIY PROM
02-11-2014, 04:47 PM
Replies: 12
Views: 2,142
Posted By Tim C

Re: $0d TBI MAF setup questions

Thanks dimented! That would help a bunch. I've been googling and reading until my eyes hurt, LOL.
Forum: DIY PROM
02-10-2014, 09:27 PM
Replies: 12
Views: 2,142
Posted By Tim C

$0d TBI MAF setup questions

I posted this in the TBI forum back in December but didnt get a reply.

I've got a 78 Ford F150 rockcrawler with a 351M and a 4 speed. I've been running TBI on it for a few years with the 7747...
Forum: TBI
12-10-2013, 08:45 PM
Replies: 0
Views: 592
Posted By Tim C

TBI with MAF questions

I don't know if this belongs here or in DIY-PROM so if I've got it in the wrong place could a mod move it for me?

I've got a 78 Ford F150 rockcrawler with a 351M and a 4 speed:eek:. I've been...
Forum: TBI
12-10-2013, 08:28 PM
Replies: 3
Views: 2,244
Posted By Tim C

Re: Has anyone done TBI swap on 260-289 Ford

Im running TBI on a 78 F150 with a 351M. I'm running a chevy 350 manual transmission computer and triggering the chevy ignition module with the stock ford duraspark distributor. The purple or...
Showing results 1 to 24 of 24


 
Forum Jump


All times are GMT -5. The time now is 05:56 PM.