Third Generation F-Body Message Boards

Search: Posts Made By: Noahshenk
Showing results 1 to 19 of 19
Search took 0.01 seconds.
Forum: Suspension and Chassis
03-18-2024, 03:39 AM
Replies: 1
Views: 197
Posted By Noahshenk

inner fender metal

So I had a project i thought i just finished, but after some digging i might not actually be done. My strut tower had a hole the i patched with an equal piece of metal a bit smaller than a credit...
Forum: Tech / General Engine
05-21-2023, 02:14 AM
Replies: 4
Views: 850
Posted By Noahshenk

Re: stock piston ring end gap

its by no means a high performance engine. just something to get the car up and running with a simple cam, carb, and headers.
Forum: Tech / General Engine
05-19-2023, 07:36 PM
Replies: 4
Views: 850
Posted By Noahshenk

stock piston ring end gap

Doing a rebuild of my 350 and just bought the "Sealed power Performance Piston Ring Set" (part# SLP-E-251K) to go onto my stock pistons (1975 4 bolt). just wondering on where about my end gap should...
Forum: Tech / General Engine
04-29-2023, 10:57 AM
Replies: 3
Views: 1,213
Posted By Noahshenk

Re: crank and cam bearing health

Tearing into it mostly to see the health and do some precautionary maintenance which was just going to be rod bearings and an oil pump. Bought the engine for $250 a couple months back. have been...
Forum: Tech / General Engine
04-28-2023, 09:35 PM
Replies: 3
Views: 1,213
Posted By Noahshenk

crank and cam bearing health

Just wondering if the damage to the front of my crank and front-most cam bearing is too far to be put in the engine. any input is appreciated ...
Forum: Transmissions and Drivetrain
04-01-2023, 01:57 PM
Replies: 6
Views: 882
Posted By Noahshenk

Re: TKX - American powertrain

Planning on using the lakewood 15000LKW
Forum: Transmissions and Drivetrain
03-29-2023, 03:43 PM
Replies: 6
Views: 882
Posted By Noahshenk

Re: TKX - American powertrain

I was planning on getting a lakewood bell housing, so no problems there.
Forum: Transmissions and Drivetrain
03-29-2023, 02:09 AM
Replies: 6
Views: 882
Posted By Noahshenk

TKX - American powertrain

Planning on getting a Tremec TKX to bolt to my 350 and was wondering... Is the American Powertrains TKX kit necessary if I already have a T-5 in the car? Has anyone done it without the kit? I've also...
Forum: Carburetors
03-28-2023, 11:03 PM
Replies: 7
Views: 775
Posted By Noahshenk

Re: fuel pressure regulator on carb with EFP

Aren't the return and supply lines different sizes though?
Forum: Carburetors
03-24-2023, 12:46 AM
Replies: 7
Views: 775
Posted By Noahshenk

fuel pressure regulator on carb with EFP

So I'm swapping a 350 into my V6 1989 firebird, in which I just installed a brand new in-tank fuel pump. From reading the V6 to V8 swap thread I know I need a 3 to 1 fuel pressure regulator with a...
Forum: Transmissions and Drivetrain
03-12-2023, 03:09 PM
Replies: 4
Views: 766
Posted By Noahshenk

Re: TKX clutch assembly question

My numbers will be a touch below that, but a little overkill will give me some wiggle room to play if I decide to add some more! Do you have the part numbers for those parts? Thanks!
Forum: Transmissions and Drivetrain
03-11-2023, 08:07 PM
Replies: 4
Views: 766
Posted By Noahshenk

TKX clutch assembly question

I plan on swapping a TKX 5 speed to go behind my 1977 4 bolt main 350, which I believe is a two piece rear main seal. What is a good streetable flywheel, clutch, and pressure plate combo for my...
Forum: Transmissions and Drivetrain
03-11-2023, 06:44 PM
Replies: 27
Views: 13,908
Posted By Noahshenk

Re: TO INSTALL A TREMEC TKX TRANSMISSION

Is the Hydraulic clutch kit necessary for the swap, or can it be done without? Also, what benefits do you gain from having a hydraulic vs mechanical clutch? Can a stock T-5 driveshaft be used or will...
Forum: Transmissions and Drivetrain
03-04-2023, 11:41 PM
Replies: 5
Views: 388
Posted By Noahshenk

Re: Built T5 vs T-56 swap

my 350 is a two piece RMS so I would need to get a different flywheel (+$400)
Forum: Body
03-04-2023, 12:16 AM
Replies: 1
Views: 397
Posted By Noahshenk

Re: favor needed 2.8 V6 owners

Any idea if these decals were on firebirds? I have an 89 I could check:huh:
Forum: Transmissions and Drivetrain
03-04-2023, 12:13 AM
Replies: 5
Views: 388
Posted By Noahshenk

Built T5 vs T-56 swap

Hey all. Just crunching numbers and trying to decide with to go with a T-56 swap to go along with my (soon to be) built 77’ 350 sbc or if I should get my T-5 built by G-Force Transmissions. I’ve got...
Forum: Tech / General Engine
02-02-2023, 03:44 PM
Replies: 2
Views: 319
Posted By Noahshenk

Trouble with fuel rail

I’m a bit new to third gens, so bear with me. I got an 89 2.8l firebird that I’m fixing up. Was sitting for a while before I bought it. In an attempt to get it fired up I took the fuel rail out along...
Forum: TPI
10-29-2021, 10:22 PM
Replies: 7
Views: 524
Posted By Noahshenk

Re: Gas Tank fitment '89 firebird

I dont have jack stands so Its on ramps atm. all suspension is still together. Like I said I cant seem to find where its hitting it just wont slip in. I guess I'll have to invest in some jack stands...
Forum: TPI
10-29-2021, 04:39 PM
Replies: 7
Views: 524
Posted By Noahshenk

Gas Tank fitment '89 firebird

I hope this is the right message board but I just picked up an 89 V6 manual firebird with a bad fuel pump. PO had already taken everything out including the tank and both panhard bars. Ordered an...
Showing results 1 to 19 of 19


 
Forum Jump


All times are GMT -5. The time now is 05:58 PM.