Third Generation F-Body Message Boards

Search: Posts Made By: onebad84z28
Showing results 1 to 14 of 14
Search took 0.10 seconds.
Forum: Carburetors
10-01-2005, 07:13 AM
Replies: 2
Views: 620
Posted By onebad84z28

The carb will be close usually right out of the...

The carb will be close usually right out of the box to get the car running and break the cam in ,but you will need to fine tune the idle mixture screws, also i found the carb to be a little lean on...
Forum: Organized Drag Racing and Autocross
09-26-2005, 04:18 PM
Replies: 9
Views: 628
Posted By onebad84z28

thanks for all the calculations ,what brand drag...

thanks for all the calculations ,what brand drag radials would you reccomend?( M/T or BFG ) I notice on m/t site they reccomend a 8 rim for 235 60 15 i know i could score some 15" z28 rims cheap but...
Forum: Organized Drag Racing and Autocross
09-25-2005, 02:11 PM
Replies: 9
Views: 628
Posted By onebad84z28

I did four runs first one was how i drove it in...

I did four runs first one was how i drove it in last 3 lower tires down to 24 lbs, and i know that i am spining a little of the line maybe first 10 to 15 ft .i am sure some drag radial would help....
Forum: Organized Drag Racing and Autocross
09-25-2005, 01:07 PM
Replies: 9
Views: 628
Posted By onebad84z28

thanks for the reply. the temp was 60, ba was...

thanks for the reply. the temp was 60, ba was 30.34 and the humidity was 45%, the track is listed at 100 feet above sea level.
Forum: Organized Drag Racing and Autocross
09-25-2005, 09:46 AM
Replies: 9
Views: 628
Posted By onebad84z28

converting 1/4 mile time into horsepower,are the converter close?

Car ran 14.68 at sea level, stock 15"radial ta tires ,transmission and 3.23 gears. car with me 3600 lbs. Has a eaton posi, subframe conectors,banks cat back , hedman headers and y pipe coated and...
Forum: Tech / General Engine
09-20-2005, 07:36 PM
Replies: 31
Views: 2,421
Posted By onebad84z28

Factory horsepower ratings are done with all...

Factory horsepower ratings are done with all accessories installed and operating,and are measured at rear of the transmission.This is from chiltons repair manual. also says it may vary from model to...
Forum: Organized Drag Racing and Autocross
05-23-2005, 04:53 PM
Replies: 9
Views: 610
Posted By onebad84z28

I live in the Burlington area, i go to canada...

I live in the Burlington area, i go to canada every weekend to spend time with my fiance who lives in st jean which about 20 minutes from Napierville dragway, might take this car to see what it will...
Forum: Organized Drag Racing and Autocross
05-22-2005, 03:22 PM
Replies: 9
Views: 610
Posted By onebad84z28

The one in Milton been closed for 25 years. I...

The one in Milton been closed for 25 years. I wish there was one here in Vermont
Forum: Exhaust
04-25-2005, 05:48 PM
Replies: 3
Views: 533
Posted By onebad84z28

My hedman y pipe is part number 17470 and was 2.5...

My hedman y pipe is part number 17470 and was 2.5 where the two pipes came together. The funny thing is it s 3 inch where they meet but they reduce it down to 2.5. I also at the same time change my...
Forum: Exhaust
04-24-2005, 07:03 PM
Replies: 3
Views: 533
Posted By onebad84z28

Me and my friend just did this to my heddman y...

Me and my friend just did this to my heddman y pipe, it was 2.5 we cut it of and used a 3" 90 and 45 bend. cut the 90 to get the right angle and mig it together. Then I sent it to jet hot to have it...
Forum: Exhaust
04-21-2005, 07:40 PM
Replies: 16
Views: 1,133
Posted By onebad84z28

What we did to my y pipe was cut it where they...

What we did to my y pipe was cut it where they merge into one and weld a 90 degree and 45 degree bend cut to fit and mig weld it together,now i have two 2 1/4 into a 3" pipe instead of going into a 2...
Forum: Exhaust
04-19-2005, 08:52 PM
Replies: 16
Views: 1,133
Posted By onebad84z28

bull ,i just went from a dynomax 2.5 cat back to...

bull ,i just went from a dynomax 2.5 cat back to a 3 " banks and change my hedman y pipe to 3 where the pipes come together to the cat and let me tell you what a differnce. i had a bog off the line i...
Forum: Tech / General Engine
05-24-2004, 06:08 PM
Replies: 9
Views: 741
Posted By onebad84z28

thanks for the replys ,looks like drilled to deep...

thanks for the replys ,looks like drilled to deep so i am going to try to seal it just that way. took it over to friend that help put the motor together he said the same thing,and the leak has almost...
Forum: Tech / General Engine
05-23-2004, 10:47 AM
Replies: 9
Views: 741
Posted By onebad84z28

head leaking out header bolt

hi, put some new sr torquer 305 heads on my z28 and now i have coolant leak out of the last header bolt on the driver side. wondering if anyone had this problem or heard of this problem with these...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 03:40 AM.