Third Generation F-Body Message Boards

 
Page 1 of 5
1
2
3
4
5
Search: Posts Made By: 86z28iroc-z
Showing results 1 to 50 of 206
Search took 0.13 seconds.
Forum: Exhaust
04-07-2010, 09:07 PM
Replies: 6
Views: 934
Posted By 86z28iroc-z

Re: true duals no cats!

+1 for true duals over any y-pipe or x-pipe.

I just built up true duals with pypes m80s mufflers for my 357 with a mild cam and I can now chirp second which I couldn't with a single y-pipe...
Forum: DIY PROM
08-23-2009, 09:24 PM
Replies: 7
Views: 694
Posted By 86z28iroc-z

Re: Knocking above 1900rpms

Yeah, it knocks with the exhaust on and with it off.

Not sure what would have caused carbon to build up with a motor that is only 8000 miles old. But it def isn't lean, the blms and ints are +or-...
Forum: DIY PROM
08-16-2009, 05:14 PM
Replies: 7
Views: 694
Posted By 86z28iroc-z

Re: Knocking above 1900rpms

Took out all the spark plugs, found alot of carbon/flakey build up on the #3, replaced it, took all the plug wires off and tested them, 117-138ohm, took the cap off and noticed that one of the...
Forum: DIY PROM
08-16-2009, 01:01 PM
Replies: 7
Views: 694
Posted By 86z28iroc-z

Re: Knocking above 1900rpms

Where is a good place to start looking?
Forum: DIY PROM
08-15-2009, 10:18 PM
Replies: 7
Views: 694
Posted By 86z28iroc-z

Knocking above 1900rpms

Built up a 355 with a mild cam and TPI about 2 years ago, and i've got about 9000 miles on it, i had it tuned perfectly 0 knock counts from 0rpms to 5500rpms any gear any speed...

Decided I...
Forum: Tech / General Engine
08-15-2009, 09:58 PM
Replies: 2
Views: 425
Posted By 86z28iroc-z

Re: Knocking above 1900rpms

It is, my base timing is set @ 6*, my advanced timing around the 1900rpm in third gear is 27-28* and I had it reduced 10* to 17* and it still knocks. Meaning it's not a too much timing issue.
Forum: Tech / General Engine
08-15-2009, 09:17 PM
Replies: 2
Views: 425
Posted By 86z28iroc-z

Knocking above 1900rpms

Built up a 355 with a mild cam and TPI about 2 years ago, and i've got about 9000 miles on it, i had it tuned perfectly 0 knock counts from 0rpms to 5500rpms any gear any speed...

Decided I wanted...
Forum: DIY PROM
05-01-2009, 04:32 PM
Replies: 3
Views: 1,161
Posted By 86z28iroc-z

Re: Weird values during OPEN LOOP, fine in closed

I did some poking around and found that it is dependant on the set time of closed loop timer, and the SA is 20* plus whatever is in the Spark Correction - LV8 vs coolant temp table. and it'll sit at...
Forum: DIY PROM
05-01-2009, 11:43 AM
Replies: 3
Views: 1,161
Posted By 86z28iroc-z

Re: Weird values during OPEN LOOP, fine in closed

Everything is normal/perfect in closed loop. My BLMS are 124 when really cold and 129 when not as cold in open loop and it stays around 128 in closed loop +-1or2 the only thing that's weird is my SA...
Forum: DIY PROM
04-30-2009, 09:50 PM
Replies: 3
Views: 1,161
Posted By 86z28iroc-z

Weird values during OPEN LOOP, fine in closed

Not sure if this is normal for OPEN LOOP, but i just noticed lately that if I start my car from a cold start, and let it warm up for a good minute and took off, it felt like it had no power, and then...
Forum: DFI and ECM
04-12-2009, 03:44 PM
Replies: 7
Views: 1,962
Posted By 86z28iroc-z

Re: Standalone OBD-I Datalogger

Looking into the scanmaster, and that is pretty cool, but it only allows you to view one parameter at a time, you can view o2 and knock continuously but you have to cycle thru the modes to view...
Forum: DFI and ECM
04-12-2009, 03:37 PM
Replies: 7
Views: 1,962
Posted By 86z28iroc-z

Re: Standalone OBD-I Datalogger

Craig didn't have nething he was working on for the obd1 system...will keep looking!
Forum: DFI and ECM
04-05-2009, 10:44 PM
Replies: 7
Views: 1,962
Posted By 86z28iroc-z

Re: Standalone OBD-I Datalogger

Def have to email him, i've already got the burn1 and have done quite abit of datalogging and tuning with a homemade cable and a laptop on the pass. seat, just thought it'd be easier to have a...
Forum: DFI and ECM
03-31-2009, 06:06 PM
Replies: 7
Views: 1,962
Posted By 86z28iroc-z

Re: Standalone OBD-I Datalogger

I'd like it to be standalone, meaning I wouldn't need to hook a laptop up, just have a little screen that is permanently in the car.

I did look at that before tho, it looks like a nice system.
Forum: DFI and ECM
03-31-2009, 01:14 PM
Replies: 7
Views: 1,962
Posted By 86z28iroc-z

Standalone OBD-I Datalogger

There are a plethora of standalone OBD-II dataloggers out there, but not a single one for obd-I atleast that I havn't found yet...

I want something like the dashdaq shown here >...
Forum: Exhaust
02-26-2009, 01:12 PM
Replies: 8
Views: 1,754
Posted By 86z28iroc-z

Re: Running exhaust under the axle

No1 has a response to the how that guy ran his exhaust?
Forum: Interior Parts for Sale
02-25-2009, 08:14 AM
Replies: 28
Views: 807
Posted By 86z28iroc-z

Re: PARTING OUT 1991 FIREBIRD IN DETROIT MICHIGAN

What rear end does it have? Let me know!
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-23-2009, 10:21 PM
Replies: 24
Views: 844
Posted By 86z28iroc-z

Re: Parting out 1985 Z28!! All parts available

I'm looking for a 3.23 posi drum/disc let me know, freight to 58027.
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-23-2009, 10:16 PM
Replies: 9
Views: 368
Posted By 86z28iroc-z

Re: 90 CAMARO RS V6 AUTO PARTING OUT INQUIRIES.....

I'm looking for a 3.23 posi drum/disc let me know.
Forum: Exhaust
02-23-2009, 09:22 PM
Replies: 8
Views: 1,754
Posted By 86z28iroc-z

Re: Running exhaust under the axle

Heh, I should posted my initial idea first.

I have to have the extra pipe off the cutout because it sounds like an old tractor without a longer tailpipe, plus the logner pipe is needed to place my...
Forum: Exhaust
02-23-2009, 12:42 PM
Replies: 8
Views: 1,754
Posted By 86z28iroc-z

Running exhaust under the axle

Doing a new exhaust setup and putting an electric exhaust cutout somewhere in the I-pipe and running a tailpipe off of it to have it exit on the passenger side out the back.

Was wondering if it...
Forum: Engine/Drivetrain/Suspension Wanted
02-19-2009, 07:19 PM
Replies: 3
Views: 330
Posted By 86z28iroc-z

3.23 Posi Complete Drum or Disc 86-02

In need of a non-whining rear end.

Must be 3.23.

Must be Working Posi.

Must be mostly complete.

Will travel 200 miles one way to pickup for $50.
Forum: Exhaust
02-16-2009, 02:26 PM
Replies: 5
Views: 1,256
Posted By 86z28iroc-z

Re: Ideal Pipe Size for mild TPI motor

In my understanding a bigger pipe would actually hurt performance in the low-mid range which my car makes most of it's power, it's only 230hp to the wheels and 310tq in the 3000-4500 rpm range. That...
Forum: Exhaust
02-16-2009, 01:07 PM
Replies: 5
Views: 1,256
Posted By 86z28iroc-z

Re: Ideal Pipe Size for mild TPI motor

Reading over all the stickies and looking at other posts and sites, i've noticed that a 3" pipe is ideal for 350 that peaks between 5500-6500 rpms, so knowing that, wouldn't a 2.5" pipe be better for...
Forum: Exhaust
02-12-2009, 09:16 PM
Replies: 5
Views: 1,256
Posted By 86z28iroc-z

Re: 2.5" y-pipe to 3" inter. pipe? Where to get?

Edited.
Forum: Exhaust
02-12-2009, 09:11 PM
Replies: 6
Views: 1,692
Posted By 86z28iroc-z

Re: Smell from exhaust

I'd have to say that 100 LL is the best smelling gas. Not that it's street legal or nething, do you have a cat installed? It'll stink if you don't have a cat.
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-10-2009, 11:27 PM
Replies: 8
Views: 702
Posted By 86z28iroc-z

Re: 3inch madrel bent y pipe, Hawks Headers!

You sure love your Mt.Dew!
Forum: Exhaust
02-10-2009, 09:46 PM
Replies: 5
Views: 1,256
Posted By 86z28iroc-z

Ideal Pipe Size for mild TPI motor

I recently put hedmann shorty headers on a mildly rebuilt 350 tpi motor and they came with a 2.5" y-pipe, the only two y-pipes that come with hedmann headers are 2.5".

Is it even worth it to mate...
Forum: Exhaust
02-09-2009, 11:24 PM
Replies: 12
Views: 5,046
Posted By 86z28iroc-z

Re: Loudest Catalytic Convertor

heh, thanks, it's a v8 (357 TPI mild cam, worked heads) had to go with single out to achieve the sound I wanted.
Forum: Exhaust
02-05-2009, 10:47 PM
Replies: 12
Views: 5,046
Posted By 86z28iroc-z

Re: Loudest Catalytic Convertor

I think she's too smart to fall for the placebo effect,

Something wrong with the speedo? Whatcha mean?

"Some" power lol, not too much, better than the old 305 tho.


New question, would...
Forum: Exhaust
02-05-2009, 09:42 AM
Replies: 12
Views: 5,046
Posted By 86z28iroc-z

Re: Loudest Catalytic Convertor

heh, i was starting to wonder myself if every1 just read the title, heres a clip of what it sounds like as is...and I don't want to lose the idle, it's raw and mean.

Also, I do not have any laws...
Forum: Exhaust
02-04-2009, 10:40 PM
Replies: 12
Views: 5,046
Posted By 86z28iroc-z

Loudest Catalytic Convertor

Well, I have FINALLY achieved my ideal exhaust sound (shorty headers, y-pipe, no cat, straight pipe, muffler delete, single exit, resonator tip) and I want to try and clean up the exhaust smell,...
Forum: Exhaust
02-04-2009, 10:38 PM
Replies: 8
Views: 1,088
Posted By 86z28iroc-z

Re: Silent exhaust

Scary quiet exhaust is the Hooker Maximum flow muffler, it's single in, single out, and flows the same as open pipe.

If you can live with single in/single out, it's the way to go.

Without a cat...
Forum: Exterior Parts for Sale
06-09-2008, 10:22 PM
Replies: 51
Views: 1,677
Posted By 86z28iroc-z

Re: Parting out 91 RS and 89 WS6

Have you sold the whole set of gfx off the camaro? Does it include a high-rise spoiler?

Any cracks or holes??

How much for the whole set shipped to 58027??

Let me know!

-Tyler
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-24-2008, 02:31 PM
Replies: 15
Views: 2,328
Posted By 86z28iroc-z

Re: 2 K&N Filters & Hooker Maxflow Muffler

K&N's sold

Mufflers still for sale!
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-15-2008, 06:54 PM
Replies: 15
Views: 2,328
Posted By 86z28iroc-z

Re: 2 K&N Filters & Hooker Maxflow Muffler

K&N's can go for $25 shipped.
Maxflow can go for $60 shipped.
Glasspack can go for $22 shipped.
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-10-2008, 09:53 PM
Replies: 15
Views: 2,328
Posted By 86z28iroc-z

Re: 2 K&N Filters & Hooker Maxflow Muffler

Bump for the weekend!
Forum: Exterior Parts for Sale
05-08-2008, 12:51 PM
Replies: 4
Views: 357
Posted By 86z28iroc-z

Re: Parking Lights 85-92 camaro $20 shipped

Sale Pending
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-08-2008, 12:19 AM
Replies: 15
Views: 1,236
Posted By 86z28iroc-z

Re: Borla race muffler

Have any clips? Can you take a picture of the inlet, showing the insides?
Forum: Exterior Parts for Sale
05-07-2008, 11:34 AM
Replies: 4
Views: 357
Posted By 86z28iroc-z

Re: Parking Lights 85-92 camaro $20 shipped

Cleaned them up a little bit.

http://i79.photobucket.com/albums/j159/tyroach123/DSC00707.jpg

http://i79.photobucket.com/albums/j159/tyroach123/DSC00715.jpg
Forum: Aftermarket Product Review
05-07-2008, 10:30 AM
Replies: 13
Views: 1,764
Posted By 86z28iroc-z

Re: High-Flow... low volume muffler???

If you can live with a single exit, or fab up a custom y-pipe out the exit to a dual pipe setup, the Hooker Maximum flow flows the same as 2.5" straight pipe, and is quiet....almost too quiet, on the...
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-07-2008, 12:19 AM
Replies: 15
Views: 2,328
Posted By 86z28iroc-z

Re: 2 K&N Filters & Hooker Maxflow Muffler

Here is a short startup and rev video. Mounted it in the stock muffler location with the turndown faced out. Camera is rattling from the deepness, and doesn't quite pick up the deep rumble very well....
Forum: Exterior Parts for Sale
05-06-2008, 10:00 PM
Replies: 4
Views: 357
Posted By 86z28iroc-z

Parking Lights 85-92 camaro $20 shipped

20 bux shipped

http://i79.photobucket.com/albums/j159/tyroach123/DSC00693.jpg

http://i79.photobucket.com/albums/j159/tyroach123/DSC00696.jpg
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-06-2008, 02:00 PM
Replies: 11
Views: 1,460
Posted By 86z28iroc-z

Re: Interests in my custom 3inch chambered tube catback??

I think he's referring to this setup. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=150239128846

But if you look it is not mandrel bent and does not include a chambered muffler.
...
Showing results 1 to 50 of 206
 
Page 1 of 5
1
2
3
4
5


 
Forum Jump


All times are GMT -5. The time now is 02:14 AM.