Loose steering with Lakewood control arms
#1
Member
Thread Starter
Join Date: Dec 2001
Location: Orange, CA
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 305 L69
Transmission: 700R4
Loose steering with Lakewood control arms
Hi all, I just installed Lakewood rear lower control arms. Now the steering feels very loose and the car gets swervy around higher speed curves. I'm going to remove them if there's not an easy fix. I've got Energy Suspension front control arm bushings that aren't installed yet, would that help. This car is strickly for street, not auto-x or drag, I just wanted to improve the handling a bit. Any help would be appreciated.
Thanks, Gary
Thanks, Gary
#2
Supreme Member
Join Date: Mar 2001
Location: Portland, OR www.cascadecrew.org
Posts: 6,577
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Camaro RS
Engine: Juiced 5.0 TBI - 300rwhp
Transmission: T5
Axle/Gears: 3.42 Eaton Posi, 10 Bolt
the lakewoods are a poly bushing squar tube? correct?
if so , it is possible that your rear suspension is acutaly going into 'bind' as you go arround the corner, and the inside spring compresses, the "twisting" motion of the rear may be hampered by the lack of twising in the LCA and Poly bushing, causing the bind, and making your car oversteer.
just a thought, i am not saying this IS what is happening, but i think it is a possibility.
edit: BTW, when you say loose can you explian more, does the steering wheel feel loose, or is the rear end actualy loosing traction, and oversteering, i re-read you post, and realised you may not be talkign about "loose" handling (as in oversteer)
if so , it is possible that your rear suspension is acutaly going into 'bind' as you go arround the corner, and the inside spring compresses, the "twisting" motion of the rear may be hampered by the lack of twising in the LCA and Poly bushing, causing the bind, and making your car oversteer.
just a thought, i am not saying this IS what is happening, but i think it is a possibility.
edit: BTW, when you say loose can you explian more, does the steering wheel feel loose, or is the rear end actualy loosing traction, and oversteering, i re-read you post, and realised you may not be talkign about "loose" handling (as in oversteer)
#3
Supreme Member
Join Date: Jul 1999
Location: Loveland, OH, US
Posts: 18,457
Likes: 0
Received 15 Likes
on
15 Posts
Car: 4
Engine: 6
Transmission: 5
They had no such effect on my car. The poly deflects entirely enough to provide all the protection against binding that is needed.
Sounds like you disconnected the Panhard bar at some point during the install, and left it unhooked.
Sounds like you disconnected the Panhard bar at some point during the install, and left it unhooked.
#5
Member
Thread Starter
Join Date: Dec 2001
Location: Orange, CA
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 305 L69
Transmission: 700R4
Yes Dewey, by loose, I mean the steering wheel has some play in it and when steering imput does seem to engage I do get oversteer. I didn't disconnect the panhard bar as RB83L69 suggests. I torqed the bolts to 68 lbs as the manual suggests but I didn't tighten them with the suspension loaded. Also, I have always had a vibration on the freeway above 65, and now I have a lot more.
Gary
The Lakewoods are square tube with Poly bushings
Gary
The Lakewoods are square tube with Poly bushings
Last edited by Holio; 12-16-2002 at 04:13 PM.
#6
TGO Supporter
i didnt have any problem with my lakewood rear control arms..
you may get some more road noise with poly bushings..
i didnt take/lossen my panhard bar at all either, i did one side at a time and called it done..
did you put greese in them?
you may get some more road noise with poly bushings..
i didnt take/lossen my panhard bar at all either, i did one side at a time and called it done..
did you put greese in them?
#7
Junior Member
Join Date: Oct 2001
Location: Quad Cites Area IL Side
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
in the body shop we always tighten suspension components with the cars weight on the wheels that way there will be no bind on the bushings. best way to do this is on an alignment rack.
Thread
Thread Starter
Forum
Replies
Last Post
New2Chevy
Engine/Drivetrain/Suspension Parts for Sale
2
09-28-2015 12:35 AM
TheTraut88
Engine/Drivetrain/Suspension Parts for Sale
1
09-07-2015 05:22 PM
1Aauto
Sponsored Vendors
0
09-02-2015 01:35 PM