Help me get MOOG springs in :(
#1
Help me get MOOG springs in :(
Hey,
I been working on my car off and on for a while now. My landlord wants me to move the car so I got some cheap MOOG springs from summit. I tried jacking them up by the ball joint on the a-arms and compressing them...
No matter how much I compress or jack the never go in properly. How are you guys doing this?
I need this done asap and am working with little time. My main reason for using the MOOG in the first places is that I have Deep Dish Y2k's and I don't know if they will rub with drop springs and 2" spacers. Should I just give up and buy drop springs??
FRONT WHEEL SIZE: 18x9.5
FRONT WHEEL OFFSET: 54
REAR WHEEL SIZE: 19x10
REAR WHEEL OFFSET: 65
BOLT PATTERN: 5-120.65
HUB SIZE: 70.3
I been working on my car off and on for a while now. My landlord wants me to move the car so I got some cheap MOOG springs from summit. I tried jacking them up by the ball joint on the a-arms and compressing them...
No matter how much I compress or jack the never go in properly. How are you guys doing this?
I need this done asap and am working with little time. My main reason for using the MOOG in the first places is that I have Deep Dish Y2k's and I don't know if they will rub with drop springs and 2" spacers. Should I just give up and buy drop springs??
FRONT WHEEL SIZE: 18x9.5
FRONT WHEEL OFFSET: 54
REAR WHEEL SIZE: 19x10
REAR WHEEL OFFSET: 65
BOLT PATTERN: 5-120.65
HUB SIZE: 70.3
Last edited by blakecharles; 01-02-2013 at 03:08 PM.
#2
Re: Help me get MOOG springs in :(
Here are some pix of what I'm talking about... Here is a pic after the safty chain was removed.
- if I jack the a-arm up to the ball joint, the spring will no seat properly
- the compressor will not compress spring small enough to get into the seat
- if I remove the a-arm, put the spring into the seat and jack up into the car it seats properly but then the car lifts off the jackstands... EVEN WITH THE ls1/t56 IN THE CAR!!
- if I jack the a-arm up to the ball joint, the spring will no seat properly
- the compressor will not compress spring small enough to get into the seat
- if I remove the a-arm, put the spring into the seat and jack up into the car it seats properly but then the car lifts off the jackstands... EVEN WITH THE ls1/t56 IN THE CAR!!
#3
Re: Help me get MOOG springs in :(
Here is the spindle mod and the Deep Dish Y2k w/ LS1 Brakes that I have been trying to put on the car. Will these rub with drop springs?
#4
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,652
Likes: 0
Received 46 Likes
on
44 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: Help me get MOOG springs in :(
You will probably need a spring compressor to get them in, some of the moogs are pretty stiff. Also, with those a-arms, I used a piece of household electrical wire, 12-2 romex, to wrap around the sprin and the back of the a-arm pocket to tie/strap things in place until the spring starts to seat. Made life easier.
#7
Member
Join Date: Sep 2006
Location: Birmingham, MI
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1983 Crossfire Recaro T/A
Engine: 5.0L Crossfire
Transmission: Upgraded 700R4
Axle/Gears: 3:23
Re: Help me get MOOG springs in :(
I also could not get Moogs to fit. I had the correct part number for my application and used an inside compressor and still fought it for two days. Finally the compressor slipped off and the spring popped free and fractured a bone in my hand.
The spring was confirmed many times to be the correct replacement, however it was smaller in diameter and slightly taller than the original springs. My original springs fit in with no compressor. After significant damage to my person, it just made more sense to go with what fit.
Not to say they can't fit, but I think with the taller height it was not going to be easy. If you have dropped your spindles even more from stock, you are fighting an even tougher fight than I had.
Once again, not saying it can't be done and not saying you shouldn't try, but the lowering springs may be an easier approach.
No idea if they will interfere with what you have done. Buy them, try them, and take them back for a refund if they interfere.
Good luck and be SAFE!
The spring was confirmed many times to be the correct replacement, however it was smaller in diameter and slightly taller than the original springs. My original springs fit in with no compressor. After significant damage to my person, it just made more sense to go with what fit.
Not to say they can't fit, but I think with the taller height it was not going to be easy. If you have dropped your spindles even more from stock, you are fighting an even tougher fight than I had.
Once again, not saying it can't be done and not saying you shouldn't try, but the lowering springs may be an easier approach.
No idea if they will interfere with what you have done. Buy them, try them, and take them back for a refund if they interfere.
Good luck and be SAFE!
Trending Topics
#8
Re: Help me get MOOG springs in :(
Now my problem is that I already spent money on the MOOGs and need the sport-lines too soon send the MOOGs back... smh. I will let you know how it go's.
#9
#10
Supreme Member
iTrader: (1)
Re: Help me get MOOG springs in :(
Read that link. Trust me you can get them in but you need the hook tool compressor and the piece of pipe. You will not get them in any other way. Idk about the Eibach ones either. I heard they are npt as stiff lb wise because stock is 700+lbs and up and the Eibachs are 600lbs If im not mistaken. But from what Ive read they are taller by a little. Trust guys who have done ot this way with that link. Its a fight to get the hooks dead on , but in you driveway on your own this is the best way. I also used a impqct gun to tighten down the compressor tool, makes life easier. And what 86 TA said have a backup plan always when doing this swap. Wrap the coils with small chains or wire or something. The other poster got lucky with a fracture. Ive seen broken jaws. If the tool arms slip, break or any thing the backup plan will safe your ***, or any other body parts that would be in the line of fire. Let us know how it works out. Take care and be safe, dont rush something to get it done. Do it right and safe once.
#11
Member
iTrader: (1)
Re: Help me get MOOG springs in :(
Yep, if you have to you can just cut them and they'll pop right in, just make sure you cut both springs evenly or you'll mess up your x-weights and the car will handle like crap if you drive it with those springs in. Weight jacks and some of the lowering springs with a large drop are easy to install too.
I fought a spring compressor over the summer when I put my Del-alums in my a-arms. Extremely tedious and nerve racking, treat the spring like a loaded gun and keep it pointed away from your face or body. If you can run a safety chain while you wind it down that's even better. You can get the springs in there, though they'll give a hell of a fight... but when you get them in it's a great feeling.
I fought a spring compressor over the summer when I put my Del-alums in my a-arms. Extremely tedious and nerve racking, treat the spring like a loaded gun and keep it pointed away from your face or body. If you can run a safety chain while you wind it down that's even better. You can get the springs in there, though they'll give a hell of a fight... but when you get them in it's a great feeling.
#12
Supreme Member
iTrader: (4)
Re: Help me get MOOG springs in :(
I had way more luck with a 3 foot crowbar than with a spring compressor... next time I have the springs out Im doing a video. Anchor the crowbar at the top of the spring pocket, far side. Seat the top of the spring where it needs to be in the K-member and hold it there with the crowbar.
Now you push up the crowbar and use your feet to push the spring downhill across the crowbar and into the spring pocket. When it gets to where it needs to be you yank the crowbar out. This will give safety ***** a heart attack but as long as you dont do it barefoot its not dangerous at all. You dont have feet under the spring, just beside it, and your feet being against it will keep it from shooting out somewhere. I messed it up at least a half dozen times before I got it in right, no injuries to speak of. Im terrified of spring compressors and I felt much safer doing it this way.
Just make sure when you are setting up the spring, that you index it right before you start sliding it into place.
Now you push up the crowbar and use your feet to push the spring downhill across the crowbar and into the spring pocket. When it gets to where it needs to be you yank the crowbar out. This will give safety ***** a heart attack but as long as you dont do it barefoot its not dangerous at all. You dont have feet under the spring, just beside it, and your feet being against it will keep it from shooting out somewhere. I messed it up at least a half dozen times before I got it in right, no injuries to speak of. Im terrified of spring compressors and I felt much safer doing it this way.
Just make sure when you are setting up the spring, that you index it right before you start sliding it into place.
#13
Supreme Member
iTrader: (1)
Re: Help me get MOOG springs in :(
I had way more luck with a 3 foot crowbar than with a spring compressor... next time I have the springs out Im doing a video. Anchor the crowbar at the top of the spring pocket, far side. Seat the top of the spring where it needs to be in the K-member and hold it there with the crowbar.
Now you push up the crowbar and use your feet to push the spring downhill across the crowbar and into the spring pocket. When it gets to where it needs to be you yank the crowbar out. This will give safety ***** a heart attack but as long as you dont do it barefoot its not dangerous at all. You dont have feet under the spring, just beside it, and your feet being against it will keep it from shooting out somewhere. I messed it up at least a half dozen times before I got it in right, no injuries to speak of. Im terrified of spring compressors and I felt much safer doing it this way.
Just make sure when you are setting up the spring, that you index it right before you start sliding it into place.
Now you push up the crowbar and use your feet to push the spring downhill across the crowbar and into the spring pocket. When it gets to where it needs to be you yank the crowbar out. This will give safety ***** a heart attack but as long as you dont do it barefoot its not dangerous at all. You dont have feet under the spring, just beside it, and your feet being against it will keep it from shooting out somewhere. I messed it up at least a half dozen times before I got it in right, no injuries to speak of. Im terrified of spring compressors and I felt much safer doing it this way.
Just make sure when you are setting up the spring, that you index it right before you start sliding it into place.
#14
Supreme Member
iTrader: (4)
Re: Help me get MOOG springs in :(
I cant picture it. Your going to have to video it. Are you leg pressing the spring into place? Never heard of this method. The spring compressor way I Like because I have everything powder coated if it wasnt I wouldnt care about jamming the spring in there. With the compressor less chance to screw ip the paint scheme.
This method I feel is a lot safer since the spring doesnt get compressed NEARLY as much as with a compressor, but it definitely results in springs bouncing around (harmlessly) if you dont get it right, and if you're trying to figure it out, you wont get it right the first few times. So it most likely will scratch up things here and there.
Lol I made a hilarious picture of how I do it:
Last edited by InfernalVortex; 01-07-2013 at 02:45 AM.
#15
Member
Join Date: Dec 2012
Posts: 228
Likes: 0
Received 1 Like
on
1 Post
Car: 1990 z28
Engine: 5.0
Transmission: t-5 wc
Axle/Gears: 4th gen 3.42 posi
Re: Help me get MOOG springs in :(
as you said in your first post ,if you remove the a arm it will seat . well pet on the ball joint (not all the way ) just 3-4 turns drop the rear of the arm (2 mtg bolts ) put the spring in , place the jack under the back bar of the a arm ,not under the spring! jack into place when it gets close enough stick a screwdriver through one of the mtg bolt holes wile you line up the other one for the bolt , bolt it up then work the other one .if you have to move the jack before you remove the screwdriver. use a block of wood with a notch cut in it . this can be very dangerous if the jack isn't lined op properly . so if you begin this way and dont feel good about it ..... then dont do it this way!!!!!!!
#16
Supreme Member
iTrader: (1)
Re: Help me get MOOG springs in :(
Actually leg pressing the spring in there is an excellent description. I compress with the crowbar and use the bottoms of my feet to slide the spring down the crowbar and guide it. You get the bar up high enough and the spring will naturally slide "Downhill" and the key is to get the end of the crowbar in the spring pocket area just right so the spring hops off of it and straight into the spring cup.
This method I feel is a lot safer since the spring doesnt get compressed NEARLY as much as with a compressor, but it definitely results in springs bouncing around (harmlessly) if you dont get it right, and if you're trying to figure it out, you wont get it right the first few times. So it most likely will scratch up things here and there.
Lol I made a hilarious picture of how I do it:
This method I feel is a lot safer since the spring doesnt get compressed NEARLY as much as with a compressor, but it definitely results in springs bouncing around (harmlessly) if you dont get it right, and if you're trying to figure it out, you wont get it right the first few times. So it most likely will scratch up things here and there.
Lol I made a hilarious picture of how I do it:
#17
Supreme Member
Join Date: Aug 2003
Location: Long Island New York
Posts: 1,644
Likes: 0
Received 3 Likes
on
3 Posts
Car: 89 Formula 350
Engine: Forged 385 H/C/I
Transmission: 700R4-4300 Stall-lockup
Axle/Gears: BW 9 Bolt 3:70
Re: Help me get MOOG springs in :(
Looks like you really need a spring compressor. I would think it would be easier if after you install the A-arm to then attach the spindle before attaching to the strut.
#18
Member
Re: Help me get MOOG springs in :(
LOL that actually how I got my GC springs into my UMI A arms, I also had a mini jack under the a arm, had to hold the crow bar in one hand and use the jack with the other
#19
Supreme Member
iTrader: (4)
Re: Help me get MOOG springs in :(
Ok if your by yourself who is jacking up the a arm when the spring is compressed? Im pretty strong i wouldnt try that. Hook spring compressor, 4 inch piece of pipe, small diameter safty chains and a jack under the a arm. You will have to compress the spring almost closed to get it in there, no way around it. Read that thread again op.
Theoretically, If you can get the a-arm the right angle, the spring will hold itself in place and the spring seat will still be low enough to get it in there. It looks awkward and isnt in there very good, but it will stay, because I was able to do it. It may pop out, but it's barely compressed at that point, not much residual energy stored in the spring when only one side of it is barely compressed. The biggest danger is the weight of the spring scratching something as it falls or falling onto your toe. No real force behind it, just gravity.
The other method of attaching hte balljoint and spindle and taking out the a-arm bolts will also work, but I had a hard time getting mine to do that properly without it just lifting the car. And then you need two jacks for the front and back corners of the a-arm. The spring is a lot closer to that side of the a-arm so its harder to get leverage against it. It can work, but with lighter cars and higher spring rates that are stock height springs it may not be as fool proof.
Last edited by InfernalVortex; 01-07-2013 at 05:29 PM.
#20
Re: Help me get MOOG springs in :(
That pic scares the hell outta me! lol! I managed to get the drivers side in using the 3 1/2 pipe method. It didn't go right in, I had to position one of the compressor arms lower than the other so that the spring compressed at an angle.
It was the angle that allowed the spring to sit in both the A-arm and K-member pockets at the same time. After the spring was installed I was not able to remove the compressor, so I ended up taking it apart inside the spring.
I started installing the Movetech steering linkage and the UMI sleeves.
It was the angle that allowed the spring to sit in both the A-arm and K-member pockets at the same time. After the spring was installed I was not able to remove the compressor, so I ended up taking it apart inside the spring.
I started installing the Movetech steering linkage and the UMI sleeves.
#21
Re: Help me get MOOG springs in :(
Makes me wonder how the stock springs where put in, these new MOOG springs are a good bit shorter than what came off the car. Here is a pic before I tried the 3 1/2 pipe method.
#22
Senior Member
iTrader: (8)
Join Date: Sep 2008
Location: San Fernando valley-Lancaster,CA
Posts: 682
Likes: 0
Received 1 Like
on
1 Post
Car: '86 TRANS-AM WS6
Engine: 1989 355 TPI L98
Transmission: TH700R-4
Axle/Gears: BorgWarner 9 bolt/ 3.27
Re: Help me get MOOG springs in :(
Read that link. Trust me you can get them in but you need the hook tool compressor and the piece of pipe. You will not get them in any other way. Idk about the Eibach ones either. I heard they are npt as stiff lb wise because stock is 700+lbs and up and the Eibachs are 600lbs If im not mistaken. But from what Ive read they are taller by a little. Trust guys who have done ot this way with that link. Its a fight to get the hooks dead on , but in you driveway on your own this is the best way. I also used a impqct gun to tighten down the compressor tool, makes life easier. And what 86 TA said have a backup plan always when doing this swap. Wrap the coils with small chains or wire or something. The other poster got lucky with a fracture. Ive seen broken jaws. If the tool arms slip, break or any thing the backup plan will safe your ***, or any other body parts that would be in the line of fire. Let us know how it works out. Take care and be safe, dont rush something to get it done. Do it right and safe once.
#23
Re: Help me get MOOG springs in :(
I went to home depot and got a pipe from the plumbing section (was only $1). I put it on the compressor and it did help but even with this method I was not able to get the other spring in.
In the end I ended up scratching up my freshly powder coated A-Arms so I took them off. I was not able to get the spring to sit into the pocket properly with both the spring and a-arm off the car. Even on the side that I get it on, it just barely fits (no play at all). The stock springs are not as wide and the coil is not as thick so they fit into the a-arm and have room to play. I checked and verified the parts number is right!
Nothing works, I'm leaving the spring in there crooked and bringing the car to a Racing shop around the corner. Or I may end up just buying the drop springs from summit.
In the end I ended up scratching up my freshly powder coated A-Arms so I took them off. I was not able to get the spring to sit into the pocket properly with both the spring and a-arm off the car. Even on the side that I get it on, it just barely fits (no play at all). The stock springs are not as wide and the coil is not as thick so they fit into the a-arm and have room to play. I checked and verified the parts number is right!
Nothing works, I'm leaving the spring in there crooked and bringing the car to a Racing shop around the corner. Or I may end up just buying the drop springs from summit.
#24
Re: Help me get MOOG springs in :(
I learned my lesson... I have scratched my new a-arms and wasted money on MOOGs when I could have just paid the extra $100 for the drop springs from the start. I been working on this over a week. I'm calling this a loss, springs are in the garbage.
There is no way to make these fit. Thanx everyone!
There is no way to make these fit. Thanx everyone!
#25
Re: Help me get MOOG springs in :(
BUMP!!
Okay,
I ditched the MOOG's. I was never able to get both sides to seat properly into the spring pockets even with the A-Arms off the car. one side just would not fit, spring seemed too wide. I tapped them into the a-arms then could not get them out (fit was tight). I was told that it would have worked fine with stock A-arms (and I think that's true)...
I ended up getting these instead. Should I run these with insulators? If I don't will I be too low??
Okay,
I ditched the MOOG's. I was never able to get both sides to seat properly into the spring pockets even with the A-Arms off the car. one side just would not fit, spring seemed too wide. I tapped them into the a-arms then could not get them out (fit was tight). I was told that it would have worked fine with stock A-arms (and I think that's true)...
I ended up getting these instead. Should I run these with insulators? If I don't will I be too low??
#26
Supreme Member
iTrader: (1)
Re: Help me get MOOG springs in :(
BUMP!!
Okay,
I ditched the MOOG's. I was never able to get both sides to seat properly into the spring pockets even with the A-Arms off the car. one side just would not fit, spring seemed too wide. I tapped them into the a-arms then could not get them out (fit was tight). I was told that it would have worked fine with stock A-arms (and I think that's true)...
I ended up getting these instead. Should I run these with insulators? If I don't will I be too low??
Okay,
I ditched the MOOG's. I was never able to get both sides to seat properly into the spring pockets even with the A-Arms off the car. one side just would not fit, spring seemed too wide. I tapped them into the a-arms then could not get them out (fit was tight). I was told that it would have worked fine with stock A-arms (and I think that's true)...
I ended up getting these instead. Should I run these with insulators? If I don't will I be too low??
You might want to pull those moogs out of the dumpster before you try to get those in. Those eibach springs are said to be taller than the moogs hut at a lower lb rate. 600 if im not mistaken, the moogs are around 715. Which moogs did you get? Idk if the 305 rs springs are different than the irocz 350 ones. I think they are. I assume the higher lb you go the shorter and fatter the coils. The less lbs you go they get taller and thinner. Make sure. Im not questioning your ability but getting these springs in are not that tough even by yourself. I used the pipe and bought a few heavy duty washers to space it up and down the coils. You have to hit it right at the right spots to get full compression to get them in. Why is it easier with factory a arms vs yours? Wondering because Im putting in umi set and k member in soon. Idk if i was local id stop by to help you out.
#27
Supreme Member
Join Date: Feb 2007
Location: Andover, NJ
Posts: 1,275
Likes: 0
Received 0 Likes
on
0 Posts
Car: '88 Trans Am GTA; '84 Trans Am
Engine: L98 350TPI; 5.3 LSx built
Transmission: N/A; T56
Axle/Gears: 3.70 9 bolt; 3.73 10 bolt
Re: Help me get MOOG springs in :(
Here is a thread I found -
https://www.thirdgen.org/forums/susp...y-install.html
https://www.thirdgen.org/forums/susp...y-install.html
The Pro Kit springs are 714lb fronts, Sport lines are 700. I saw the figures somewhere.
Last edited by L695speed; 01-30-2013 at 11:09 PM.
Thread
Thread Starter
Forum
Replies
Last Post
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
7
10-08-2015 08:34 PM